参数资料
| 型号： | ATTINY2313-20SU |
| 厂商： | Atmel |
| 文件页数： | 54/225页 |
| 文件大小： | 0K |
| 描述： | IC MCU AVR 2K FLASH 20SOIC |
| 产品培训模块： | MCU Product Line Introduction tinyAVR Introduction |
| 标准包装： | 37 |
| 系列： | AVR® ATtiny |
| 核心处理器： | AVR |
| 芯体尺寸： | 8-位 |
| 速度： | 20MHz |
| 连通性： | SPI，UART/USART |
| 外围设备： | 欠压检测/复位，POR，PWM，WDT |
| 输入/输出数： | 18 |
| 程序存储器容量： | 2KB（1K x 16） |
| 程序存储器类型： | 闪存 |
| EEPROM 大小： | 128 x 8 |
| RAM 容量： | 128 x 8 |
| 电压 - 电源 (Vcc/Vdd)： | 2.7 V ~ 5.5 V |
| 振荡器型： | 内部 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 20-SOIC（0.295"，7.50mm 宽） |
| 包装： | 管件 |
| 产品目录页面： | 612 (CN2011-ZH PDF) |
| 配用： | ATSTK600-DIP40-ND - STK600 SOCKET/ADAPTER 40-PDIP ATAVRDRAGON-ND - KIT DRAGON FLASH MEM AVR ATAVRISP2-ND - PROGRAMMER AVR IN SYSTEM ATJTAGICE2-ND - AVR ON-CHIP D-BUG SYSTEM |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页当前第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页第139页第140页第141页第142页第143页第144页第145页第146页第147页第148页第149页第150页第151页第152页第153页第154页第155页第156页第157页第158页第159页第160页第161页第162页第163页第164页第165页第166页第167页第168页第169页第170页第171页第172页第173页第174页第175页第176页第177页第178页第179页第180页第181页第182页第183页第184页第185页第186页第187页第188页第189页第190页第191页第192页第193页第194页第195页第196页第197页第198页第199页第200页第201页第202页第203页第204页第205页第206页第207页第208页第209页第210页第211页第212页第213页第214页第215页第216页第217页第218页第219页第220页第221页第222页第223页第224页第225页
2009 Microchip Technology Inc.
DS41341E-page 147
PIC16F72X/PIC16LF72X
16.1
AUSART Asynchronous Mode
The AUSART transmits and receives data using the
standard non-return-to-zero (NRZ) format. NRZ is
implemented with two levels: a VOH mark state which
represents a ‘1’ data bit, and a VOL space state which
represents a ‘0’ data bit. NRZ refers to the fact that
consecutively transmitted data bits of the same value
stay at the output level of that bit without returning to a
neutral level between each bit transmission. An NRZ
transmission port idles in the mark state. Each character
transmission consists of one Start bit followed by eight
or nine data bits and is always terminated by one or
more Stop bits. The Start bit is always a space and the
Stop bits are always marks. The most common data
format is 8 bits. Each transmitted bit persists for a period
of 1/(Baud Rate). An on-chip dedicated 8-bit Baud Rate
Generator is used to derive standard baud rate
frequencies from the system oscillator. Refer to
Table 16-5 for examples of baud rate configurations.
The AUSART transmits and receives the LSb first. The
AUSART’s transmitter and receiver are functionally
independent, but share the same data format and baud
rate. Parity is not supported by the hardware, but can
be implemented in software and stored as the ninth
data bit.
16.1.1
AUSART ASYNCHRONOUS
TRANSMITTER
The AUSART transmitter block diagram is shown in
Figure 16-1. The heart of the transmitter is the serial
Transmit Shift Register (TSR), which is not directly
accessible by software. The TSR obtains its data from
the transmit buffer, which is the TXREG register.
16.1.1.1
Enabling the Transmitter
The AUSART transmitter is enabled for asynchronous
operations by configuring the following three control
bits:
TXEN = 1
SYNC = 0
SPEN = 1
All other AUSART control bits are assumed to be in
their default state.
Setting the TXEN bit of the TXSTA register enables the
transmitter circuitry of the AUSART. Clearing the SYNC
bit of the TXSTA register configures the AUSART for
asynchronous operation. Setting the SPEN bit of the
RCSTA
register
enables
the
AUSART
and
automatically configures the TX/CK I/O pin as an output.
16.1.1.2
Transmitting Data
A transmission is initiated by writing a character to the
TXREG register. If this is the first character, or the
previous character has been completely flushed from
the TSR, the data in the TXREG is immediately
transferred to the TSR register. If the TSR still contains
all or part of a previous character, the new character
data is held in the TXREG until the Stop bit of the
previous character has been transmitted. The pending
character in the TXREG is then transferred to the TSR
in
one
TCY immediately
following
the
Stop
bit
transmission. The transmission of the Start bit, data bits
and Stop bit sequence commences immediately
following the transfer of the data to the TSR from the
TXREG.
16.1.1.3
Transmit Interrupt Flag
The TXIF interrupt flag bit of the PIR1 register is set
whenever the AUSART transmitter is enabled and no
character is being held for transmission in the TXREG.
In other words, the TXIF bit is only clear when the TSR
is busy with a character and a new character has been
queued for transmission in the TXREG. The TXIF flag
bit is not cleared immediately upon writing TXREG.
TXIF becomes valid in the second instruction cycle
following the write execution. Polling TXIF immediately
following the TXREG write will return invalid results. The
TXIF bit is read-only, it cannot be set or cleared by
software.
The TXIF interrupt can be enabled by setting the TXIE
interrupt enable bit of the PIE1 register. However, the
TXIF flag bit will be set whenever the TXREG is empty,
regardless of the state of TXIE enable bit.
To use interrupts when transmitting data, set the TXIE
bit only when there is more data to send. Clear the
TXIE interrupt enable bit upon writing the last character
of the transmission to the TXREG.
Note 1: When the SPEN bit is set the RX/DT I/O pin
is automatically configured as an input,
regardless of the state of the corresponding
TRIS bit and whether or not the AUSART
receiver is enabled. The RX/DT pin data
can be read via a normal PORT read but
PORT latch data output is precluded.
2: The TXIF transmitter interrupt flag is set
when the TXEN enable bit is set.
相关PDF资料 |
PDF描述 |
|---|---|
| 70295-002 | GUIDE PIN |
| ATTINY24-20PU | IC MCU AVR 2K FLASH 20MHZ 14-DIP |
| ATTINY24V-10PU | IC MCU AVR 2K FLASH 10MHZ 14-DIP |
| ATTINY13-20SSQ | MCU AVR 1KB FLASH 20MHZ 8SOIC GW |
| ATTINY13-20SQ | MCU AVR 1KB FLASH 20MHZ 8SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ATTINY2313-20SU SL383 | 制造商:Atmel Corporation 功能描述:MCU 8-Bit ATtiny AVR RISC 2KB Flash 3.3V/5V 20-Pin SOIC W T/R |
| ATTINY2313-20SU SL514 | 制造商:Atmel Corporation 功能描述: |
| ATTINY2313-20SUR | 功能描述:8位微控制器 -MCU AVR 2KB FLSH 128B EE 128B SRAM 1UART 20P RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| ATTINY2313-20SUR SL514 | 制造商:Atmel Corporation 功能描述: |
| ATTINY2313A | 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:8-bit Microcontroller with 2/4K Bytes In-System Programmable Flash |
发布紧急采购，3分钟左右您将得到回复。