- 您现在的位置：买卖IC网 > PDF目录298849 > AYF331535 15 CONTACT(S), FEMALE, RIGHT ANGLE FFC/FPC CONNECTOR, SURFACE MOUNT PDF资料下载
参数资料
| 型号： | AYF331535 |
| 元件分类： | SMT连接器& FFC/FPC |
| 英文描述： | 15 CONTACT(S), FEMALE, RIGHT ANGLE FFC/FPC CONNECTOR, SURFACE MOUNT |
| 封装： | ROHS COMPLIANT |
| 文件页数： | 5/5页 |
| 文件大小： | 433K |
| 代理商： | AYF331535 |
FPC CONNECTORS COMMON CAUTIONS FOR USE
COMMON CAUTIONS FOR USE
PC board design
Design the recommended foot pattern in
order to secure the mechanical strength
in the soldered areas of the terminal.
FPC and equipment design
Design the FPC based on the
recommended dimensions to ensure the
required connector performance.
In addition, carefully check the equipment
design and take required measures for
the equipment to prevent the FPC from
being removed subsequent to a fall,
vibration, or other impact due to the FPC
size, weight, or the reaction force of the
routed FPC.
Connector mounting
In case the connector is picked up by
chucking during mounting, an excessive
mounter chucking force may deform the
molded or metal part of the connector.
Consult us in advance if chucking is to be
applied.
Soldering
1) Manual soldering.
Due to the low prole, if an excessive
amount of solder is applied to this
product during manual soldering, the
solder may creep up to near the contact
points, or interference by solder may
cause imperfect contact.
Make sure that the soldering iron tip is
heated within the temperature and time
limits indicated in the specications.
Flux from the solder wire may adhere to
the contact surfaces during soldering
operations. After soldering, carefully
check the contact surfaces and clean off
any ux before use.
Be aware that a load applied to the
connector terminals while soldering may
displace the contact.
Thoroughly clean the iron tip.
2) Reow soldering
Screen-printing is recommended for
printing paste solder.
Y3FT/Y3F/Y3B
Y5S
Screen thickness of 120
m is
recommended for paste solder printing.
Consult us when using a screen-printing
thickness other than that recommended.
Depending on the size of the connector
being used, self alignment may not be
possible. Accordingly, carefully position
the terminal with the PC board pattern.
The recommended reow temperature
prole is given in the gure below
Recommended reow temperature
prole
Y3FT/Y3F/Y3B
Y5S
Y5F
The temperature is measured on the
surface of the PC board near the
connector terminal.
Some solder and ux types may cause
serious solder creeping. Take the solder
and ux characteristics into consideration
when setting the reow soldering
conditions.
When performing reow soldering on
the back of the PC board after reow
soldering the connector, secure the
connector using, for example, an
adhesive. (Double reow soldering on the
same side is possible)
3) Reworking on a soldered portion
Finish reworking in one operation.
For reworking of the solder bridge, use
a soldering iron with a at tip. Do not add
ux, otherwise, the ux may creep to the
contact parts.
Use a soldering iron whose tip
temperature is within the temperature
range specied in the specications.
Do not drop the product or handle
carelessly. Otherwise, the terminals
may become deformed due to
excessive force or the solderability
during reow soldering may degrade.
Don’t open/close the lever or insert/
remove an FPC until the connector is
soldered. Forcibly applied external
pressure on the terminals can weaken
the adherence of the terminals to the
molded part or cause the terminals to
lose their evenness. In addition, do
not insert an FPC into the connector
before soldering the connector.
When cutting or bending the PC
board after mounting the connector,
be careful that the soldered sections
are subjected to excessive forces.
Other Notes
When coating the PC board after
soldering the connector to prevent the
deterioration of insulation, perform the
coating in such a way so that the coating
does not get on the connector.
The connectors are not meant to be used
for switching.
To determine the relationship between
the screen opening area and the PC
board foot pattern area, refer to the
diagrams in the recommended
patterns for PC boards and metal
masks when setting.
Note that excess solder on the
terminals prevents complete insertion
of the FPC, and that excess solder on
the metal clips prevents the lever from
rotating.
Note that excess solder inhibits the
slider lock operation.
Terminal
Paste solder
PC board foot pattern
150
°C
180
°C
230
°C
220
°C
200
°C
260
°C
Temperature
Upper limit (Soldering heat resistance)
Lower limit (Solder wettability)
Preheating
Peak temperature
Time
25 sec.
70 sec.
60 to 120 sec.
250
°C
200
°C
180
°C
150
°C
Time
Peak temperature
Preheating
60 to 120 sec.
Min. 200
°C,
70 sec.
Temperature
260
°C
200
°C
180
°C
150
°C
Time
Peak temperature
Preheating
60 to 120 sec.
Min. 200
°C,
70 sec.
Temperature
Do not the soldered areas to be subjected to forces
panasonic-electric-works.net/ac
For other details, please verify with
the product specication sheets.
相关PDF资料 |
PDF描述 |
|---|---|
| AYU1-1P-02676-120 | BOARD TERMINATED, MALE, RF CONNECTOR, SURFACE MOUNT |
| AYU1-1S13-D0251-000(LF) | CABLE TERMINATED, FEMALE, RF CONNECTOR, SOCKET |
| AYU1-1S21-S0800-213W(LF) | CABLE TERMINATED, FEMALE, RF CONNECTOR, SOCKET |
| AYZ0202AGRL | SLIDE SWITCH, DPDT, LATCHED, 0.1A, 12VDC, SURFACE MOUNT-STRAIGHT |
| AYZ0203AGRL | SLIDE SWITCH, DP3T, LATCHED, 0.1A, 12VDC, SURFACE MOUNT-STRAIGHT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AYF331535A | 功能描述:15 Position FPC Connector Contacts, Top and Bottom 0.012" (0.30mm) Surface Mount, Right Angle 制造商:panasonic electric works 系列:Y3B 包装:剪带 零件状态:有效 扁平柔性类型:FPC 安装类型:表面贴装，直角 连接器/触头类型:触头，上和下 针脚数:15 间距:0.012"（0.30mm） 端接:焊接 FFC，FCB 厚度:0.20mm 板上高度:0.036"（0.90mm） 锁定功能:翻转锁定，背锁 电缆端类型:锥形 触头材料:铜合金 触头镀层:金 外壳材料:液晶聚合物（LCP） 致动器材料:液晶聚合物（LCP） 特性:- 额定电压:50V 工作温度:-55°C ~ 85°C 材料可燃性等级:UL94 V-0 额定电流:0.2A/触头 标准包装:500 |
| AYF331565 | 功能描述:FFC & FPC连接器 FPC Connectors 0.3mm, 15 contacts RoHS:否 制造商:JAE Electronics 产品类型:Plugs 系列:HD 节距:0.5 mm 位置/触点数量:40 安装角: 安装风格:Cable 外壳材料:Plastic 触点材料:Copper Alloy 触点电镀:Gold 电压额定值:100 V per contact 电流额定值:0.24 A to 1 A |
| AYF331735 | 制造商:Panasonic Electric Works 功能描述:FPC CONNECTOR Y3B (0.3MM PITCH, |
| AYF331735A | 功能描述:CONN FPC 17POS 0.30MM R/A 制造商:panasonic electric works 系列:Y3B 包装:剪带 零件状态:在售 扁平柔性类型:FPC 安装类型:表面贴装，直角 连接器/触头类型:触头，上和下 针脚数:17 间距:0.012"（0.30mm） 端接:焊接 FFC，FCB 厚度:0.20mm 板上高度:0.036"（0.90mm） 锁定功能:翻转锁定，背锁 电缆端类型:锥形 触头材料:铜合金 触头镀层:金 外壳材料:液晶聚合物（LCP） 致动器材料:液晶聚合物（LCP） 特性:- 额定电压:50V 工作温度:-55°C ~ 85°C 材料可燃性等级:UL94 V-0 额定电流:0.2A/触头 触头镀层厚度:闪光 外壳颜色:- 致动器颜色:- 配接次数:20 标准包装:500 |
| AYF331765 | 功能描述:FFC & FPC连接器 FPC Connectors 0.3mm, 17 contacts RoHS:否 制造商:JAE Electronics 产品类型:Plugs 系列:HD 节距:0.5 mm 位置/触点数量:40 安装角: 安装风格:Cable 外壳材料:Plastic 触点材料:Copper Alloy 触点电镀:Gold 电压额定值:100 V per contact 电流额定值:0.24 A to 1 A |
发布紧急采购，3分钟左右您将得到回复。