- 您现在的位置：买卖IC网 > PDF目录18177 > B32656S8155K561 (EPCOS Inc)FILM CAP 1.5000UF 10% 850V MKP PDF资料下载
参数资料
| 型号： | B32656S8155K561 |
| 厂商： | EPCOS Inc |
| 文件页数： | 23/29页 |
| 文件大小： | 0K |
| 描述： | FILM CAP 1.5000UF 10% 850V MKP |
| 标准包装： | 32 |
| 系列： | B32656S |
| 电容： | 1.5µF |
| 额定电压 - AC： | 450V |
| 额定电压 - DC： | 850V |
| 电介质材料： | 聚丙烯，金属化 |
| 容差： | ±10% |
| ESR（等效串联电阻）： | 5 毫欧 |
| 工作温度： | -55°C ~ 110°C |
| 安装类型： | 通孔 |
| 封装/外壳： | 径向 |
| 端子： | PC 引脚 |
| 引线间隔： | 1.476"（37.50mm） |
| 特点： | 交流和双倍脉冲 |
| 包装： | 散装 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页当前第23页第24页第25页第26页第27页第28页第29页
B32656S
Snubber (wound)
1.3
General notes on soldering
Permissible heat exposure loads on film capacitors are primarily characterized by the upper cate-
gory temperature T max . Long exposure to temperatures above this type-related temperature limit
can lead to changes in the plastic dielectric and thus change irreversibly a capacitor's electrical
characteristics. For short exposures (as in practical soldering processes) the heat load (and thus
the possible effects on a capacitor) will also depend on other factors like:
Pre-heating temperature and time
Forced cooling immediately after soldering
Terminal characteristics:
diameter, length, thermal resistance, special configurations (e.g. crimping)
Height of capacitor above solder bath
Shadowing by neighboring components
Additional heating due to heat dissipation by neighboring components
Use of solder-resist coatings
The overheating associated with some of these factors can usually be reduced by suitable coun-
termeasures. For example, if a pre-heating step cannot be avoided, an additional or reinforced
cooling process may possibly have to be included.
EPCOS recommends the following conditions:
Pre-heating with a maximum temperature of 110 ° C
Temperature inside the capacitor should not exceed the following limits:
MKP/MFP 110 ° C
MKT 160 ° C
When SMD components are used together with leaded ones, the leaded film capacitors should
not pass into the SMD adhesive curing oven. The leaded components should be assembled af-
ter the SMD curing step.
Leaded film capacitors are not suitable for reflow soldering.
Uncoated capacitors
For uncoated MKT capacitors with lead spacings ≤ 10 mm (B32560/B32561) the following mea-
sures are recommended:
pre-heating to not more than 110 ° C in the preheater phase
rapid cooling after soldering
Please read Cautions and warnings and
Important notes at the end of this document.
Page 23 of 29
相关PDF资料 |
PDF描述 |
|---|---|
| DF12.1356.4110.1 | MOD PWR ENTRY 4A 250V SCREW |
| B32656S7474K561 | FILM CAP 0.4700UF 10% 1250V |
| IXTH22N50P | MOSFET N-CH 500V 22A TO-247 |
| FVXO-PC73B-256 | OSC 256 MHZ 3.3V PECL SMD |
| FOXLF160-20 | CRYSTAL 16.0 MHZ 20PF |
相关代理商/技术参数 |
参数描述 |
|---|---|
| B32656S8155K562 | 功能描述:FILM CAP MKP SNUBBER 1.5F 10% 85 制造商:epcos (tdk) 系列:* 零件状态:有效 标准包装:128 |
| B32656S8155K566 | 功能描述:FILM CAP MKP SNUBBER 1.5F 10% 85 制造商:epcos (tdk) 系列:* 零件状态:有效 标准包装:128 |
| B32656S8185561 | 制造商:EPCOS 制造商全称:EPCOS 功能描述:Film Capacitors Metallized Polyester Film Capacitors (MKT) |
| B32656S8185562 | 制造商:EPCOS 制造商全称:EPCOS 功能描述:Film Capacitors Metallized Polyester Film Capacitors (MKT) |
| B32656S8185563 | 制造商:EPCOS 制造商全称:EPCOS 功能描述:Film Capacitors Metallized Polyester Film Capacitors (MKT) |
发布紧急采购，3分钟左右您将得到回复。