- 您现在的位置：买卖IC网 > PDF目录18946 > B57550G0503F000 (EPCOS Inc)THERMISTOR NTC 50K OHM 1% RAD PDF资料下载
参数资料
| 型号： | B57550G0503F000 |
| 厂商： | EPCOS Inc |
| 文件页数： | 12/19页 |
| 文件大小： | 0K |
| 描述： | THERMISTOR NTC 50K OHM 1% RAD |
| 产品目录绘图： | B57550G0x0xF000 Side |
| 标准包装： | 1,000 |
| 系列： | B57550 |
| 在 25°C 时的电阻（欧姆）： | 50k |
| 电阻公差： | ±1% |
| B 值公差： | ±1% |
| B25/85： | 3992K |
| B25/100： | 4006K |
| 工作温度： | -55°C ~ 200°C |
| 功率 - 最大： | 32mW |
| 长度 - 引线： | 2.80"（71.00mm） |
| 安装类型： | 通孔 |
| 封装/外壳： | 珠，玻璃 |
| 包装： | 散装 |
| 其它名称： | 495-2134 B57550G 503F B57550G503F |
Temperature measurement
Glass-encapsulated sensors
Mounting instructions
B57550G, B57550G1
G550/G1550
1
1.1
Soldering
Leaded NTC thermistors
Leaded thermistors comply with the solderability requirements specified by CECC.
When soldering, care must be taken that the NTC thermistors are not damaged by excessive
heat. The following maximum temperatures, maximum time spans and minimum distances have
to be observed:
Dip soldering
Iron soldering
Bath temperature
Soldering time
Distance from thermistor
max. 260 ° C
max. 4 s
min. 6 mm
max. 360 ° C
max. 2 s
min. 6 mm
Under more severe soldering conditions the resistance may change.
1.2
Leadless NTC thermistors
In case of NTC thermistors without leads, soldering is restricted to devices which are provided
with a solderable metallization. The temperature shock caused by the application of hot solder
may produce fine cracks in the ceramic, resulting in changes in resistance.
To prevent leaching of the metallization, solder with silver additives or with a low tin content
should be used. In addition, soldering methods should be employed which permit short soldering
times.
2
Clamp contacting
Pressure contacting by means of clamps is particularly suitable for applications involving frequent
switching and high turn-on powers.
3
Robustness of terminations (leaded types)
The leads meet the requirements of IEC 60068-2-21. They may not be bent closer than 4 mm
from the solder joint on the thermistor body or from the point at which they leave the feed-
throughs. During bending, any mechanical stress at the outlet of the leads must be removed. The
bending radius should be at least 0.75 mm.
Tensile strength:
Test Ua1:
Leads
Please read Cautions and warnings and
Important notes at the end of this document.
0.25 <
0.35 <
0.50 <
0.80 <
? ≤ 0.25 mm = 1.0 N
? ≤ 0.35 mm = 2.5 N
? ≤ 0.50 mm = 5.0 N
? ≤ 0.80 mm = 10.0 N
? ≤ 1.25 mm = 20.0 N
Page 12 of 19
相关PDF资料 |
PDF描述 |
|---|---|
| DS1822 | IC THERMOMETER ECONO DIG TO-92 |
| 507-4860-3732-500F | LED PANEL IND 14V 20MA GREEN |
| AH1460619-A | SWITCH MINI SPDT PLUNG GOLD PCB |
| 559-6401-003F | LED PANEL DAYLT WHT SNAP-IN 6"LD |
| 559-6201-003F | LED PANEL DAYLT GRN SNAP-IN 6"LD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| B57550G0503F002 | 制造商:EPCOS 制造商全称:EPCOS 功能描述:NTC thermistors for temperature measurement |
| B57550G0503G000 | 制造商:EPCOS 制造商全称:EPCOS 功能描述:NTC thermistors for temperature measurement |
| B57550G0503G002 | 制造商:EPCOS 制造商全称:EPCOS 功能描述:NTC thermistors for temperature measurement |
| B57550G0503H000 | 制造商:EPCOS 制造商全称:EPCOS 功能描述:NTC thermistors for temperature measurement |
| B57550G0503H002 | 制造商:EPCOS 制造商全称:EPCOS 功能描述:NTC thermistors for temperature measurement |
发布紧急采购，3分钟左右您将得到回复。