参数资料
| 型号： | BA6406F-E2 |
| 厂商： | Rohm Semiconductor |
| 文件页数： | 12/16页 |
| 文件大小： | 0K |
| 描述： | IC MOTOR DVR HALF-WAVE SOP8 TR |
| 标准包装： | 2,500 |
| 应用： | 风扇电机驱动器，2 相 |
| 输出数： | 1 |
| 电流 - 输出： | 70mA |
| 电源电压： | 4 V ~ 28 V |
| 工作温度： | -40°C ~ 100°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.173"，4.40mm 宽） |
| 供应商设备封装： | 8-SOP |
| 包装： | 带卷 (TR) |
BD6701F
Datasheet
● Operational Notes
1) Absolute maximum ratings
An excess in the absolute maximum rations, such as supply voltage, temperature range of operating conditions, etc.,
can break down the devices, thus making impossible to identify breaking mode, such as a short circuit or an open
circuit. If any over rated values will expect to exceed the absolute maximum ratings, consider adding circuit protection
devices, such as fuses.
2) Connecting the power supply connector backward
Connecting of the power supply in reverse polarity can damage IC. Take precautions when connecting the power
supply lines. An external direction diode can be added.
3) Power supply line
Back electromotive force causes regenerated current to power supply line, therefore take a measure such as placing a
capacitor between power supply and GND for routing regenerated current. And fully ensure that the capacitor
characteristics have no problem before determine a capacitor value. (when applying electrolytic capacitors,
capacitance characteristic values are reduced at low temperatures)
4) GND potential
The potential of GND pin must be minimum potential in all operating conditions. Also ensure that all terminals except
GND terminal do not fall below GND voltage including transient characteristics. However, it is possible that the motor
output terminal may deflect below GND because of influence by back electromotive force of motor. Malfunction may
possibly occur depending on use condition, environment, and property of individual motor. Please make fully
confirmation that no problem is found on operation of IC.
5) Thermal design
Use a thermal design that allows for a sufficient margin in light of the power dissipation(Pd) in actual operating
conditions.
6) Inter-pin shorts and mounting errors
Use caution when positioning the IC for mounting on printed circuit boards. The IC may be damaged if there is any
connection error or if pins are shorted together.
7) Actions in strong electromagnetic field
Use caution when using the IC in the presence of a strong electromagnetic field as doing so may cause the IC to
malfunction.
8) ASO
When using the IC, set the output transistor so that it does not exceed absolute maximum rations or ASO.
9) Thermal shut down circuit
The IC incorporates a built-in thermal shutdown circuit (TSD circuit). Operation temperature is 175 ℃ (typ.) and has a
hysteresis width of 25 ℃ (typ.). When IC chip temperature rises and TSD circuit works, the output terminal becomes an
open state. TSD circuit is designed only to shut the IC off to prevent thermal runaway. It is not designed to protect the
IC or guarantee its operation. Do not continue to use the IC after operation this circuit or use the IC in an environment
where the operation of this circuit is assumed.
10) Testing on application boards
When testing the IC on an application board, connecting a capacitor to a pin with low impedance subjects the IC to
stress. Always discharge capacitors after each process or step. Always turn the IC’s power supply off before connecting
it to or removing it from a jig or fixture during the inspection process. Ground the IC during assembly steps as an
antistatic measure. Use similar precaution when transporting or storing the IC.
11) GND wiring pattern
When using both small signal and large current GND patterns, it is recommended to isolate the two ground patterns,
placing a single ground point at the ground potential of application so that the pattern wiring resistance and voltage
variations caused by large currents do not cause variations in the small signal ground voltage. Be careful not to change
the GND wiring pattern of any external components, either.
12) Capacitor between output and GND
When a large capacitor is connected between output and GND, if Vcc is shorted with 0V or GND for some cause, it is
possible that the current charged in the capacitor may flow into the output resulting in destruction. Keep the capacitor
between output and GND below 100uF.
13) IC terminal input
When Vcc voltage is not applied to IC, do not apply voltage to each input terminal. When voltage above Vcc or below
GND is applied to the input terminal, parasitic element is actuated due to the structure of IC. Operation of parasitic
element causes mutual interference between circuits, resulting in malfunction as well as destruction in the last. Do not
use in a manner where parasitic element is actuated.
14) In use
We are sure that the example of application circuit is preferable, but please check the character further more in
application to a part which requires high precision. In using the unit with external circuit constant changed, consider the
variation of externally equipped parts and our IC including not only static character but also transient character and
allow sufficient margin in determining.
www.rohm.com
? 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111 ? 15 ? 001
12/13
TSZ02201-0H1H0B100510-1-2
18.DEC.2012 Rev.002
相关PDF资料 |
PDF描述 |
|---|---|
| BA6423AF-E2 | IC FAN MOTOR DRIVER 1A SOP8 TR |
| BA6424AFS-E2 | IC FAN MOTOR DVR 1A SSOP-A16 TR |
| BA6951FS-E2 | IC DVR REVERSE MOTOR 16SSOP |
| BA78M10FP-E2 | IC REG LDO 10V .5A TO-252-3 |
| BA9743AFV-E2 | IC REG CTRLR BST INV PWM SSOPB16 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| BA6407 | 制造商:ROHM 制造商全称:Rohm 功能描述:2-phase half-wave motor driver |
| BA6407AF | 制造商:ROHM 制造商全称:Rohm 功能描述:2-phase half-wave motor driver |
| BA6407AF-E2 | 功能描述:IC MOTOR DVR HALF-WAVE SOP8 TR RoHS:是 类别:集成电路 (IC) >> PMIC - 电机和风扇控制器，驱动器 系列:- 产品变化通告:ATA683(3,4)PLQW Obsolescence 09/Aug/2012 标准包装:1 系列:- 应用:DC 电机控制器，无刷（BLDC），3 相 评估套件:可供 输出数:1 电流 - 输出:100mA 电压 - 负载:5.25 V ~ 20 V 电源电压:5.25 V ~ 20 V 工作温度:-40°C ~ 150°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-VQFN（7x7） 包装:剪切带 (CT) 其它名称:ATA6833-PLQWCT |
| BA6408FS | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Industrial Control IC |
| BA6409F | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Industrial Control IC |
发布紧急采购，3分钟左右您将得到回复。