参数资料
| 型号： | BA823F-E2 |
| 厂商： | Rohm Semiconductor |
| 文件页数： | 9/11页 |
| 文件大小： | 0K |
| 描述： | IC DRIVER SER/PAR I/O 8BIT SOP16 |
| 标准包装： | 1 |
| 类型： | 驱动器 |
| 驱动器/接收器数： | 8/0 |
| 电源电压： | 4.5 V ~ 5.5 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SOIC（0.173"，4.40mm 宽） |
| 供应商设备封装： | 16-SOP |
| 包装： | 标准包装 |
| 产品目录页面： | 1369 (CN2011-ZH PDF) |
| 其它名称： | BA823F-E2DKR |
BA823F
Technical Note
7/8
www.rohm.com
2009.06 - Rev.A
2009 ROHM Co., Ltd. All rights reserved.
●Notes for use
1. Absolute maximum ratings
An excess in the absolute maximum ratings, such as supply voltage, temperature range of operating conditions, etc., can
break down the devices, thus making impossible to identify breaking mode, such as a short circuit or an open circuit.
If any over rated values will expect to exceed the absolute maximum ratings, consider adding circuit protection devices,
such as fuses.
2. Connecting the power supply connector backward
Connecting of the power supply in reverse polarity can damage IC. Take precautions when connecting the power supply
lines. An external direction diode can be added.
3. Power supply lines
Design PCB layout pattern to provide low impedance GND and supply lines. To obtain a low noise ground and supply line,
separate the ground section and supply lines of the digital and analog blocks. Furthermore, for all power supply terminals
to ICs, connect a capacitor between the power supply and the GND terminal. When applying electrolytic capacitors in the
circuit, not that capacitance characteristic values are reduced at low temperatures.
4. GND voltage
The potential of GND pin must be minimum potential in all operating conditions.
5. Inter-pin shorts and mounting errors
Use caution when positioning the IC for mounting on printed circuit boards. The IC may be damaged if there is any
connection error or if pins are shorted together.
6. Actions in strong electromagnetic field
Use caution when using the IC in the presence of a strong electromagnetic field as doing so may cause the IC to
malfunction.
7. Testing on application boards
When testing the IC on an application board, connecting a capacitor to a pin with low impedance subjects the IC to stress.
Always discharge capacitors after each process or step. Always turn the IC's power supply off before connecting it to or
removing it from a jig or fixture during the inspection process. Ground the IC during assembly steps as an antistatic
measure. Use similar precaution when transporting or storing the IC.
8. Regarding input pin of the IC
This monolithic IC contains P+ isolation and P substrate layers between adjacent elements in order to keep them isolated.
P-N junctions are formed at the intersection of these P layers with the N layers of other elements, creating a parasitic diode
or transistor. For example, the relation between each potential is as follows:
When GND > Pin A and GND > Pin B, the P-N junction operates as a parasitic diode.
When GND > Pin B, the P-N junction operates as a parasitic transistor.
Parasitic diodes can occur inevitable in the structure of the IC. The operation of parasitic diodes can result in mutual
interference among circuits, operational faults, or physical damage. Accordingly, methods by which parasitic diodes
operate, such as applying a voltage that is lower than the GND (P substrate) voltage to an input pin, should not be used.
9. Ground Wiring Pattern
When using both small signal and large current GND patterns, it is recommended to isolate the two ground patterns,
placing a single ground point at the ground potential of application so that the pattern wiring resistance and voltage
variations caused by large currents do not cause variations in the small signal ground voltage. Be careful not to change the
GND wiring pattern of any external components, either.
Resistor
Transistor (NPN)
N
P
+
P
+
P
P substrate
GND
Parasitic element
Pin A
N
P
+
P
+
P
P substrate
GND
Parasitic element
Pin B
C
B
E
N
GND
Pin A
Parasitic
element
Pin B
Other adjacent elements
E
B
C
GND
Parasitic
element
Fig.10
Example of IC structure
相关PDF资料 |
PDF描述 |
|---|---|
| BA829 | IC DRIVER SER/PAR I/O 8BIT DIP18 |
| BBT3420-SN | TXRX QUAD MULTI-RATE 289-EBGA |
| BD3843FS-E2 | IC SOUND PROCESSOR 6CH 24SSOP |
| BD9251FV-E2 | IC PREAMP HBD PIR SENSOR 14-SSOP |
| BGF 104C E6327 | IC HSMMC FILTER/ESD PROT S-WLP-6 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| BA8240F | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Interface IC |
| BA8240FS | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Interface IC |
| BA8270F | 制造商:ROHM 制造商全称:Rohm 功能描述:Bus interface for car audio |
| BA8270F-E2 | 功能描述:IC INTERFACE BUS SOP14 TR RoHS:是 类别:集成电路 (IC) >> 专用 IC 系列:* 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- 类型:调帧器 应用:数据传输 安装类型:表面贴装 封装/外壳:400-BBGA 供应商设备封装:400-PBGA（27x27） 包装:散装 |
| BA8270FV | 制造商:未知厂家 制造商全称:未知厂家 功能描述:オーディオLSI |
发布紧急采购，3分钟左右您将得到回复。