- 您现在的位置：买卖IC网 > Datasheet目录315 > BD1604MUV-E2 (Rohm Semiconductor)IC LED DRVR WHITE BCKLGT 16-VQFN Datasheet资料下载
参数资料
| 型号： | BD1604MUV-E2 |
| 厂商： | Rohm Semiconductor |
| 文件页数： | 7/13页 |
| 文件大小： | 0K |
| 描述： | IC LED DRVR WHITE BCKLGT 16-VQFN |
| 标准包装： | 1 |
| 拓扑： | PWM，切换式电容器（充电泵） |
| 输出数： | 4 |
| 内部驱动器： | 是 |
| 类型 - 主要： | 背光 |
| 类型 - 次要： | 白色 LED |
| 频率： | 800kHz ~ 1.2MHz |
| 电源电压： | 2.7 V ~ 5.5 V |
| 输出电压： | 5V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-VFQFN 裸露焊盘 |
| 供应商设备封装： | VQFN016V3030 |
| 包装： | 标准包装 |
| 工作温度： | -30°C ~ 85°C |
| 产品目录页面： | 1371 (CN2011-ZH PDF) |
| 其它名称： | BD1604MUV-E2DKR |
BD1604MUV, BD1604MVV
Technical Note
● Cautions on layout pattern
When designing a layout pattern, lay out wires to a power line in a way that the layout pattern impedance can be minimized
and connect a bypass capacitor if necessary.
LED
VOUT
RSET
1 μ F
LED
VBAT
1 μ F
1 μ F 1 μ F
GND
Wiring from the VBAT pin
to Cin must meet a low
impedance.
LED
LED
The GND pin and
Cin must be
placed nearby.
GND
Fig.15 Example of BD1604MUV Layout Pattern
(Front, Top View)
Fig.16 Example of BD1604MUV Layout Pattern
(Rear, Top View)
● LED Current Control
There are two methods for LED current control. One method uses an external PWM signal and another changes the
resistance value of RREF (RSET) connected to the IREF (ISET) pin. For details, refer to the respective circuit examples.
Don’t make the setting of 30mA or more per channel for BD1604MUV/MVV.
1) Controlling the current by using the PWM method
The PWN signal must be input to the EN pin.
PWM signal “H” level: 1.4V or more
PWM signal “L” level: 0.4V or less
When PWM Duty is used in an area of 10% or less, the PWM cycle must be a range from 100Hz to 200Hz. When extremely
high-speed PWM control takes place, the linearity of LED current value to PWM duty is lost if the PWM duty is small (for
example, 10% or less) or it is large (for example, 90% or more).
2) Controlling the current by changing the SET resistance value
Rset-Rset1=Rset2// … //Restn.
This means that the current can be adjusted more finely by adding the types of resistance values.
ILED=480/Rset [A]
The approximate LED current can be obtained from the above expression. Because the current of 30mA or more per LED is not
permitted, make the setting in a way that the Rset resistance value can be maintained to be greater than or equal to16k ? .
Battery
C1
C2
Battery
C1
C2
Cin
VBAT
×1, ×1.5, ×2
Charge pump
VOUT
Cin
VBAT
×1, ×1.5, ×2
Charge pump
VOUT
Charge Pum p
Mode C ontrol
Over Voltage
Protect
Cout
Charge Pum p
Mode C ontrol
Over Voltage
Protect
Cout
EN
OSC
EN
OSC
PWM signal input (ON
for the signal set to High) SEL0
Vout Control
SEL0
Vout Control
SEL1
SEL2
Control
TSD
LED1
LED2
LED3
SEL1
SEL2
Control
TSD
LED1
LED2
LED3
LED4
LED4
Rset
ISET
ISET
Resistor Driver
Current Driver
Rsetn
Rset2
ISET
Rset1
ISET
Resistor Driver
Current Driver
GND
Fig.17 Controlling the Current
by Using the PWM Method
GND
Fig.18 Controlling the Current
by Changing the Resistance Value
www.rohm.com
? 2011 ROHM Co., Ltd. All rights reserved.
7/10
2011.06 - Rev.B
相关PDF资料 |
PDF描述 |
|---|---|
| BD1754HFN-TR | IC LED DRIVR WHITE BCKLGT 8-HSON |
| BD2802GU-E2 | IC LED DRIVER RGB 24-VCSP |
| BD6062GU-E2 | IC LED DRIVER FALSH VCSP85H2 |
| BD6066EKN-E2 | IC LED DRVR WHITE BCKLT 28-HVQFN |
| BD6069GUT-E2 | IC LED DRIVR WHITE BCKLGT 8-VCSP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| BD1604MVV | 制造商:ROHM 制造商全称:Rohm 功能描述:Backlight LED Drivers for Small LCD Panels (Charge Pump Type) |
| BD1604MVV-E2 | 功能描述:LED照明驱动器 Backlight LED Driver for Small Panel RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| BD1606MVV | 制造商:ROHM 制造商全称:Rohm 功能描述:Backlight LED Driver for Small LCD Panels (Charge Pump Type) |
| BD1606MVV_11 | 制造商:ROHM 制造商全称:Rohm 功能描述:Backlight LED Driver for Small LCD Panels (Charge Pump Type) |
| BD1606MVV-E2 | 功能描述:LED照明驱动器 Backlight LED Driver for Small Panel RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
发布紧急采购，3分钟左右您将得到回复。