- 您现在的位置：买卖IC网 > Datasheet目录315 > BD1604MUV-E2 (Rohm Semiconductor)IC LED DRVR WHITE BCKLGT 16-VQFN Datasheet资料下载
参数资料
| 型号： | BD1604MUV-E2 |
| 厂商： | Rohm Semiconductor |
| 文件页数： | 8/13页 |
| 文件大小： | 0K |
| 描述： | IC LED DRVR WHITE BCKLGT 16-VQFN |
| 标准包装： | 1 |
| 拓扑： | PWM，切换式电容器（充电泵） |
| 输出数： | 4 |
| 内部驱动器： | 是 |
| 类型 - 主要： | 背光 |
| 类型 - 次要： | 白色 LED |
| 频率： | 800kHz ~ 1.2MHz |
| 电源电压： | 2.7 V ~ 5.5 V |
| 输出电压： | 5V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-VFQFN 裸露焊盘 |
| 供应商设备封装： | VQFN016V3030 |
| 包装： | 标准包装 |
| 工作温度： | -30°C ~ 85°C |
| 产品目录页面： | 1371 (CN2011-ZH PDF) |
| 其它名称： | BD1604MUV-E2DKR |
BD1604MUV, BD1604MVV
Technical Note
● Notes for Use
(1) Absolute Maximum Ratings
An excess in the absolute maximum ratings, such as supply voltage, temperature range of operating conditions, etc.,
can break down devices, thus making impossible to identify breaking mode such as a short circuit or an open circuit. If
any special mode exceeding the absolute maximum ratings is assumed, consideration should be given to take physical
safety measures including the use of fuses, etc.
(2) Operating conditions
These conditions represent a range within which characteristics can be provided approximately as expected. The
electrical characteristics are guaranteed under the conditions of each parameter.
(3) Reverse connection of power supply connector
The reverse connection of power supply connector can break down ICs. Take protective measures against the
breakdown due to the reverse connection, such as mounting an external diode between the power supply and the IC’s
power supply terminal.
(4) Power supply line
Design PCB pattern to provide low impedance for the wiring between the power supply and the GND lines. In this regard,
for the digital block power supply and the analog block power supply, even though these power supplies has the same
level of potential, separate the power supply pattern for the digital block from that for the analog block, thus suppressing
the diffraction of digital noises to the analog block power supply resulting from impedance common to the wiring patterns.
For the GND line, give consideration to design the patterns in a similar manner.
Furthermore, for all power supply terminals to ICs, mount a capacitor between the power supply and the GND terminal.
At the same time, in order to use an electrolytic capacitor, thoroughly check to be sure the characteristics of the
capacitor to be used present no problem including the occurrence of capacity dropout at a low temperature, thus
determining the constant.
(5) GND voltage
Make setting of the potential of the GND terminal so that it will be maintained at the minimum in any operating state.
Furthermore, check to be sure no terminals are at a potential lower than the GND voltage including an actual electric
transient.
(6) Short circuit between terminals and erroneous mounting
In order to mount ICs on a set PCB, pay thorough attention to the direction and offset of the ICs. Erroneous mounting
can break down the ICs. Furthermore, if a short circuit occurs due to foreign matters entering between terminals or
between the terminal and the power supply or the GND terminal, the ICs can break down.
(7) Operation in strong electromagnetic field
Be noted that using ICs in the strong electromagnetic field can malfunction them.
(8) Inspection with set PCB
On the inspection with the set PCB, if a capacitor is connected to a low-impedance IC terminal, the IC can suffer stress.
Therefore, be sure to discharge from the set PCB by each process. Furthermore, in order to mount or dismount the set
PCB to/from the jig for the inspection process, be sure to turn OFF the power supply and then mount the set PCB to the
jig. After the completion of the inspection, be sure to turn OFF the power supply and then dismount it from the jig. In
addition, for protection against static electricity, establish a ground for the assembly process and pay thorough attention
to the transportation and the storage of the set PCB.
(9) Input terminals
In terms of the construction of IC, parasitic elements are inevitably formed in relation to potential. The operation of the
parasitic element can cause interference with circuit operation, thus resulting in a malfunction and then breakdown of
the input terminal. Therefore, pay thorough attention not to handle the input terminals, such as to apply to the input
terminals a voltage lower than the GND respectively, so that any parasitic element will operate. Furthermore, do not
apply a voltage to the input terminals when no power supply voltage is applied to the IC. In addition, even if the power
supply voltage is applied, apply to the input terminals a voltage lower than the power supply voltage or within the
guaranteed value of electrical characteristics.
(10) Ground wiring pattern
If small-signal GND and large-current GND are provided, It will be recommended to separate the large-current GND
pattern from the small-signal GND pattern and establish a single ground at the reference point of the set PCB so that
resistance to the wiring pattern and voltage fluctuations due to a large current will cause no fluctuations in voltages of
the small-signal GND. Pay attention not to cause fluctuations in the GND wiring pattern of external parts as well.
www.rohm.com
? 2011 ROHM Co., Ltd. All rights reserved.
8/10
2011.06 - Rev.B
相关PDF资料 |
PDF描述 |
|---|---|
| BD1754HFN-TR | IC LED DRIVR WHITE BCKLGT 8-HSON |
| BD2802GU-E2 | IC LED DRIVER RGB 24-VCSP |
| BD6062GU-E2 | IC LED DRIVER FALSH VCSP85H2 |
| BD6066EKN-E2 | IC LED DRVR WHITE BCKLT 28-HVQFN |
| BD6069GUT-E2 | IC LED DRIVR WHITE BCKLGT 8-VCSP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| BD1604MVV | 制造商:ROHM 制造商全称:Rohm 功能描述:Backlight LED Drivers for Small LCD Panels (Charge Pump Type) |
| BD1604MVV-E2 | 功能描述:LED照明驱动器 Backlight LED Driver for Small Panel RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| BD1606MVV | 制造商:ROHM 制造商全称:Rohm 功能描述:Backlight LED Driver for Small LCD Panels (Charge Pump Type) |
| BD1606MVV_11 | 制造商:ROHM 制造商全称:Rohm 功能描述:Backlight LED Driver for Small LCD Panels (Charge Pump Type) |
| BD1606MVV-E2 | 功能描述:LED照明驱动器 Backlight LED Driver for Small Panel RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
发布紧急采购，3分钟左右您将得到回复。