参数资料
| 型号： | BD3951F-E2 |
| 厂商： | Rohm Semiconductor |
| 文件页数： | 8/12页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO 5V .15A 8SOP |
| 标准包装： | 2,500 |
| 稳压器拓扑结构： | 正，固定式 |
| 输出电压： | 5V |
| 输入电压： | 6 V ~ 20 V |
| 电压 - 压降（标准）： | 0.31V @ 100mA |
| 稳压器数量： | 1 |
| 电流 - 输出： | 150mA（最小） |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.173"，4.40mm 宽） |
| 供应商设备封装： | 8-SOP |
| 包装： | 带卷 (TR) |
BD3951F
Technical Note
10. Output capacitor between output terminal and GND must be used to prevent undesirable oscillation. Ceramic Capacitor
3.3 μ F ～ 2200 μ F can be used. When selecting the value of the output capacitor, please make sure that the operation
on the actual application takes these conditions into account: rapid input or load transient response.
11. BD3951F might be damaged from the exceed inflow current from the terminals to VCC (for instance, VCC is short to
GND while the output capacitor is charging.). In those cases, VCC series diode (to prevent inflow current) or bypass
diode (connected from terminals to VCC) should be used externally in an application.
12. The over-current protection circuits are built in at the output to prevent the IC from being damaged when the load is
short-circuited or over-current. This protection circuit is droop type and designed not to latch-up in an unexpected huge
current driven.
13. BD3951F has thermal Shut Down protection (TSD) which performs Power Tr OFF in high Tj condition. If Tj increase
more than TSD temperature, output power transistor would OFF. After Tj cooled down, the device would be recovered
automatically. This function is designed for to protect the device at the accidental unexpected conditions. Since TSD
setting is higher temperature than absolute maximum ratings, thermal design must has done not to use this function.
14. Bypass capacitor 0.33 μ F ～ 10mF into the nearest position between VCC pin and GND is recommended.
15. Insert power zenner diode between VCC terminal and GND terminal is necessary, if more than 50V serge voltage would
be supplied to VCC terminals.
16. The SOUT terminal is only activated (“H”/“L”) while the RESET is “H”. While the RESET terminal is “L”, the SOUT
terminal is always “L”.
www.rohm.com
? 2009 ROHM Co., Ltd. All rights reserved.
8/9
2009.07 - Rev.A
相关PDF资料 |
PDF描述 |
|---|---|
| BD4153FV-E2 | IC PWR MGMT SWITCH 24SSOP |
| BD4154FV-E2 | IC POWER SWITCH SSOP-B20 |
| BD6212FP-E2 | IC H-BRIDGE DRIVER 1CH 2A HSOP25 |
| BD6220F-E2 | IC H-BRIDGE DRIVER 1CH 0.5A SOP8 |
| BD62321HFP-TR | IC H-BRIDGE DVR 36V 1CH 3A HRP7 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| BD3980F-E2 | 功能描述:线性稳压器 - 标准 VOLTAGE REGULATOR RoHS:否 制造商:STMicroelectronics 输出类型: 极性: 输出电压:1.8 V 输出电流:150 mA 负载调节: 最大输入电压:5.5 V 线路调整率: 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:SOT-323-5L |
| BD3985FV | 制造商:ROHM 制造商全称:Rohm 功能描述:Positive and Negative Variable Linear Regulator |
| BD3985FV_11 | 制造商:ROHM 制造商全称:Rohm 功能描述:Silicon Monolithic Integrated Circuit |
| BD3985FV-E2 | 功能描述:低压差稳压器 - LDO LDO REG -8.5-5V RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| BD3987FV | 制造商:ROHM 制造商全称:Rohm 功能描述:Positive and Negative Variable Linear Regulator |
发布紧急采购，3分钟左右您将得到回复。