参数资料
| 型号： | BD6212FP-E2 |
| 厂商： | Rohm Semiconductor |
| 文件页数： | 12/21页 |
| 文件大小： | 0K |
| 描述： | IC H-BRIDGE DRIVER 1CH 2A HSOP25 |
| 产品培训模块： | H-Bridge Drivers for DC Brush Motors |
| 特色产品： | H-Bridge Driver IC |
| 标准包装： | 1 |
| 应用： | 直流电机驱动器 |
| 评估套件： | 可供 |
| 输出数： | 1 |
| 电流 - 输出： | 2A |
| 电源电压： | 3 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 25-SOP（0.213"，5.40mm）+ 2 翼片 |
| 供应商设备封装： | 25-HSOP |
| 包装： | 标准包装 |
| 产品目录页面： | 1372 (CN2011-ZH PDF) |
| 配用： | BD6212FP-EVAL-N-ND - BOARD EVAL FOR BD6212FP |
| 其它名称： | BD6212FP-E2DKR |
BD621xxx Series
Datasheet
i) j) VREF control mode
The built-in VREF duty cycle conversion circuit provides a duty cycle corresponding to the voltage of the VREF pin
and the VCC voltage. The function offers the same level of control as the high voltage output setting function in
previous models. The duty cycle is calculated by the following equation.
DUTY ≈ VREF [V] / VCC [V]
For example, if VCC voltage is 5V and VREF pin voltage is 3.75V, the duty cycle is about 75 percent. However,
please note that the duty cycle might be limited by the range of the VREF pin voltage (Refer to the operating
conditions, shown on page 2). The PWM carrier frequency in this mode is 25kHz (nominal), and the switching
operation is the same as the PWM control modes. When operating in this mode, do not input a PWM signal to the
FIN and RIN pins. In addition, establish a current path for the recovery current from the motor, by connecting a
bypass capacitor (10μF or more is recommended) between VCC and ground.
VCC
VREF
0
FIN
RIN
OUT1
OUT2
Fig.35 VREF control operation (timing chart)
2) Cross-conduction protection circuit
In the full bridge output stage, when the upper and lower transistors are turned on at the same time during high to low
or low to high transition, an inrush current flows from the power supply to ground, resulting to a loss. This circuit
eliminates the inrush current by providing a dead time (about 400ns, nominal) during the transition.
3) Output protection circuits
a) Under voltage lock out (UVLO) circuit
To ensure the lowest power supply voltage necessary to operate the controller, and to prevent under voltage
malfunctions, a UVLO circuit has been built into this driver. When the power supply voltage falls to 2.3V (nominal) or
below, the controller forces all driver outputs to high impedance. When the voltage rises to 2.5V (nominal) or above,
the UVLO circuit ends the lockout operation and returns the chip to normal operation.
b) Over voltage protection (OVP) circuit
When the power supply voltage exceeds 7.3V (nominal), the controller forces all driver outputs to high impedance.
The OVP circuit is released and its operation ends when the voltage drops back to 6.8V (nominal) or below. This
protection circuit does not work in the stand-by mode. Also, note that this circuit is supplementary, and thus if it is
asserted, the absolute maximum rating will have been exceeded. Therefore, do not continue to use the IC after this
circuit is activated, and do not operate the IC in an environment where activation of the circuit is assumed.
www.rohm.com
? 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111 ? 15 ? 001
12/18
TSZ02201-0P2P0B300070-1-2
25.Dec.2012 Rev.002
相关PDF资料 |
PDF描述 |
|---|---|
| BD6220F-E2 | IC H-BRIDGE DRIVER 1CH 0.5A SOP8 |
| BD62321HFP-TR | IC H-BRIDGE DVR 36V 1CH 3A HRP7 |
| BD6290EFV-E2 | IC MOTOR DVR STEP BIPO 24-HTSSOP |
| BD6522F-E2 | IC PWR MANAGEMENT SWITCH SOP8 TR |
| BD6524HFV-TR | IC PWR MANAGEMENT SWITCH HVSOF6 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| BD6212FP-EVAL-N | 功能描述:BOARD EVAL FOR BD6212FP RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 标准包装:1 系列:- 主要目的:数字电位器 嵌入式:- 已用 IC / 零件:AD5258 主要属性:- 次要属性:- 已供物品:板 相关产品:AD5258BRMZ1-ND - IC POT DGTL I2C1K 64P 10MSOPAD5258BRMZ10-ND - IC POT DGTL I2C 10K 64P 10MSOPAD5258BRMZ100-ND - IC POT DGTL I2C 100K 64P 10MSOPAD5258BRMZ50-ND - IC POT DGTL I2C 50K 64P 10MSOPAD5258BRMZ1-R7-ND - IC POT DGTL I2C 1K 64P 10MSOPAD5258BRMZ10-R7-ND - IC POT DGTL I2C 10K 64P 10MSOPAD5258BRMZ50-R7-ND - IC POT DGTL I2C 50K 64P 10MSOPAD5258BRMZ100-R7-ND - IC POT DGTL I2C 100K 64P 10MSOP |
| BD6212HFP | 制造商:ROHM 制造商全称:Rohm 功能描述:H-bridge driver for DC brush motor |
| BD6212HFP-TR | 功能描述:马达/运动/点火控制器和驱动器 H-BRIDGE 7V max 1 Chan 2.0A 0.5ohm RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| BD6215 | 制造商:ROHM 制造商全称:Rohm 功能描述:H-bridge drivers (7V max.) |
| BD6216 | 制造商:ROHM 制造商全称:Rohm 功能描述:H-bridge drivers (7V max.) |
发布紧急采购，3分钟左右您将得到回复。