参数资料
| 型号： | BD6220F-E2 |
| 厂商： | Rohm Semiconductor |
| 文件页数： | 14/22页 |
| 文件大小： | 0K |
| 描述： | IC H-BRIDGE DRIVER 1CH 0.5A SOP8 |
| 产品培训模块： | H-Bridge Drivers for DC Brush Motors |
| 特色产品： | H-Bridge Driver IC |
| 标准包装： | 1 |
| 应用： | 直流电机驱动器 |
| 输出数： | 1 |
| 电流 - 输出： | 500mA |
| 电源电压： | 6 V ~ 15 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.173"，4.40mm 宽） |
| 供应商设备封装： | 8-SOP |
| 包装： | 标准包装 |
| 产品目录页面： | 1372 (CN2011-ZH PDF) |
| 其它名称： | BD6220F-E2DKR |
BD622xxx Series
Datasheet
c) Thermal shutdown (TSD) circuit
The TSD circuit operates when the junction temperature of the driver exceeds the preset temperature (175 ℃
nominal). At this time, the controller forces all driver outputs to high impedance. Since thermal hysteresis is provided
in the TSD circuit, the chip returns to normal operation when the junction temperature falls below the preset
temperature (150 ℃ nominal). Thus, it is a self-resetting circuit.
The TSD circuit is designed only to shut the IC off to prevent thermal runaway. It is not designed to protect the IC or
guarantee its operation in the presence of extreme heat. Do not continue to use the IC after the TSD circuit is
activated, and do not operate the IC in an environment where activation of the circuit is assumed.
d) Over current protection (OCP) circuit
To protect this driver IC from ground faults, power supply line faults and load short circuits, the OCP circuit monitors
the output current for the circuit’s monitoring time (10μs, nominal). When the protection circuit detects an over
current, the controller forces all driver outputs to high impedance during the off time (290μs, nominal). The IC returns
to normal operation after the off time period has elapsed (self-returning type). At the two channels type, this circuit
works independently for each channel.
Threshold
Iout
0
CTRL Input
Internal status
Monitor / Timer
ON
mon.
OFF
off timer
ON
Fig.39 Over current protection (timing chart)
● I/O equivalent circuit
VCC
VCC
VCC
VCC
FIN
RIN
100k
VREF
10k
OUT1
OUT2
OUT1
OUT2
100k
GND
RNF
GND
Fig.40 FIN / RIN
www.rohm.com
? 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111 ? 15 ? 001
Fig.41 VREF
Fig.42 OUT1 / OUT2
(SOP8/HRP7)
14/19
Fig.43 OUT1 / OUT2
(HSOP25)
TSZ02201-0P2P0B300080-1-2
25.Dec.2012 Rev.002
相关PDF资料 |
PDF描述 |
|---|---|
| BD62321HFP-TR | IC H-BRIDGE DVR 36V 1CH 3A HRP7 |
| BD6290EFV-E2 | IC MOTOR DVR STEP BIPO 24-HTSSOP |
| BD6522F-E2 | IC PWR MANAGEMENT SWITCH SOP8 TR |
| BD6524HFV-TR | IC PWR MANAGEMENT SWITCH HVSOF6 |
| BD7003NUX-E2 | IC REG LDO ADJ .3A 8VSON |
相关代理商/技术参数 |
参数描述 |
|---|---|
| BD6220HFP | 制造商:ROHM 制造商全称:Rohm 功能描述:18V max. H-bridge Drivers |
| BD6220HFP-TR | 功能描述:马达/运动/点火控制器和驱动器 H-BRIDGE 18V max 1 Chan 0.5A 1.5ohm RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| BD6221 | 制造商:ROHM 制造商全称:Rohm 功能描述:18V max. H-bridge Drivers |
| BD62210AEFV-E2 | 功能描述:HIGH PERFORMANCE, HIGH RELIABILI 制造商:rohm semiconductor 系列:* 包装:剪切带（CT） 零件状态:在售 安装类型:表面贴装 封装/外壳:28-VSSOP（0.173"，4.40mm 宽）裸露焊盘 供应商器件封装:28-HTSSOP-B 标准包装:1 |
| BD6221F | 制造商:ROHM 制造商全称:Rohm 功能描述:H-bridge driver for DC brush motor |
发布紧急采购，3分钟左右您将得到回复。