- 您现在的位置：买卖IC网 > PDF目录166429 > BD6231HFP BRUSH DC MOTOR CONTROLLER, 1 A, PSSO8 PDF资料下载
参数资料
| 型号： | BD6231HFP |
| 元件分类： | 运动控制电子 |
| 英文描述： | BRUSH DC MOTOR CONTROLLER, 1 A, PSSO8 |
| 封装： | HRP-7 |
| 文件页数： | 2/17页 |
| 文件大小： | 713K |
| 代理商： | BD6231HFP |
10/16
e) f) PWM control mode
The rotational speed of the motor can be controlled by the switching duty when the PWM signal is input to the FIN
pin or the RIN pin. In this mode, the high side output is fixed and the low side output does the switching,
corresponding to the input signal. The switching operates by the output state toggling between "L" and "Hi-Z".
The PWM frequency can be input in the range between 20kHz and 100kHz. Note that control may not be attained
by switching on duty at frequencies lower than 20kHz, since the operation functions via the stand-by mode. Also,
circuit operation may not respond correctly when the input signal is higher than 100kHz. To operate in this mode,
connect the VREF pin with VCC pin. In addition, establish a current path for the recovery current from the motor, by
connecting a bypass capacitor (10μF or more is recommended) between VCC and ground.
Control input : H
Control input : L
Fig.39 PWM control operation (output stage)
Fig.40 PWM control operation (timing chart)
g) h) VREF control mode
The built-in VREF-switching on duty conversion circuit provides switching duty corresponding to the voltage of the
VREF pin and the VCC voltage. The function offers the same level of control as the high voltage output setting
function in previous models. The on duty is shown by the following equation.
DUTY VREF [V] / VCC [V]
For example, if VCC voltage is 24V and VREF pin voltage is 18V, the switching on duty is about 75 percent.
However, please note that the switching on duty might be limited by the range of VREF pin voltage (Refer to the
operating conditions, shown on page 2). The PWM carrier frequency in this mode is 25kHz (nominal), and the
switching operation is the same as it is the PWM control modes. When operating in this mode, do not input the
PWM signal to the FIN and RIN pins. In addition, establish a current path for the recovery current from the motor,
by connecting a bypass capacitor (10μF or more is recommended) between VCC and ground.
Fig.41 VREF control operation (timing chart)
M
ON
OFF
ON
M
ON
OFF
VCC
VREF
FIN
RIN
OUT1
OUT2
0
FIN
RIN
OUT1
OUT2
相关PDF资料 |
PDF描述 |
|---|---|
| BD6718FV-E2 | BRUSHLESS DC MOTOR CONTROLLER, 0.02 A, PDSO20 |
| BD9007HFP | 2 A SWITCHING REGULATOR, 505 kHz SWITCHING FREQ-MAX, PSSO7 |
| BD9831AMWV | SWITCHING REGULATOR, 2000 kHz SWITCHING FREQ-MAX, PQCC56 |
| BD9870FPS | 1.5 A SWITCHING REGULATOR, 990 kHz SWITCHING FREQ-MAX, PSSO4 |
| BDC-062BNX-014 | 62.5/125 um, MULTI MODE, DUPLEX FIBER OPTIC CONNECTOR, PLUG |
相关代理商/技术参数 |
参数描述 |
|---|---|
| BD6231HFP-TR | 功能描述:马达/运动/点火控制器和驱动器 H-BRIDGE 36V max 1 Chan 1.0A 1.5ohm RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| BD6232 | 制造商:ROHM 制造商全称:Rohm 功能描述:H-bridge drivers (36V max.) |
| BD62321HFP | 制造商:ROHM 制造商全称:Rohm 功能描述:H-bridge driver |
| BD62321HFP-TR | 功能描述:IC H-BRIDGE DVR 36V 1CH 3A HRP7 RoHS:是 类别:集成电路 (IC) >> PMIC - 电机和风扇控制器，驱动器 系列:- 标准包装:1 系列:- 应用:直流电机驱动器，步进电机驱动器 评估套件:- 输出数:1 或 2 电流 - 输出:750mA 电压 - 负载:10 V ~ 40 V 电源电压:4.5 V ~ 5.5 V 工作温度:-20°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-BFSOP（0.295"，7.50mm 宽） 供应商设备封装:24-SOP 包装:Digi-Reel® 其它名称:MTS62C19A-HS105DKR |
| BD6232FP | 制造商:ROHM 制造商全称:Rohm 功能描述:H-Bridge Motor Drivers For DC Brush Motors |
发布紧急采购，3分钟左右您将得到回复。