- 您现在的位置：买卖IC网 > PDF目录22320 > BD6519FJ-E2 (Rohm Semiconductor)IC SWITCH HIGH SIDE 1CH SOP-J8 PDF资料下载
参数资料
| 型号： | BD6519FJ-E2 |
| 厂商： | Rohm Semiconductor |
| 文件页数： | 18/25页 |
| 文件大小： | 0K |
| 描述： | IC SWITCH HIGH SIDE 1CH SOP-J8 |
| 特色产品： | High Side Switch Regulators |
| 标准包装： | 1 |
| 类型： | 高端 |
| 输入类型： | 非反相 |
| 输出数： | 1 |
| 导通状态电阻： | 100 毫欧 |
| 电流 - 输出 / 通道： | 500mA |
| 电流 - 峰值输出： | 1A |
| 电源电压： | 3 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOP-J |
| 包装： | 标准包装 |
| 产品目录页面： | 1372 (CN2011-ZH PDF) |
| 其它名称： | BD6519FJ-E2DKR |
BD2041AFJ
BD2051AFJ
Datasheet
● Operational Notes
(1) Absolute Maximum Ratings
An excess in the absolute maximum ratings, such as supply voltage, temperature range of operating conditions, etc., can
break down devices, thus making impossible to identify breaking mode such as a short circuit or an open circuit. If any
special mode exceeding the absolute maximum ratings is assumed, consideration should be given to take physical safety
measures including the use of fuses, etc.
(2) Operating conditions
These conditions represent a range within which characteristics can be provided approximately as expected.
The electrical characteristics are guaranteed under the conditions of each parameter.
(3) Reverse connection of power supply connector
The reverse connection of power supply connector can break down ICs. Take protective measures against the
breakdown due to the reverse connection, such as mounting an external diode between the power supply and the IC’s
power supply terminal.
(4) Power supply line
Design PCB pattern to provide low impedance for the wiring between the power supply and the GND lines. In this regard,
for the digital block power supply and the analog block power supply, even though these power supplies has the same
level of potential, separate the power supply pattern for the digital block from that for the analog block, thus suppressing
the diffraction of digital noises to the analog block power supply resulting from impedance common to the wiring patterns.
For the GND line, give consideration to design the patterns in a similar manner.
Furthermore, for all power supply terminals to ICs, mount a capacitor between the power supply and the GND terminal. At
the same time, in order to use an electrolytic capacitor, thoroughly check to be sure the characteristics of the capacitor to
be used present no problem including the occurrence of capacity dropout at a low temperature, thus determining the
constant.
(5) GND voltage
Make setting of the potential of the GND terminal so that it will be maintained at the minimum in any operating state.
Furthermore, check to be sure no terminals are at a potential lower than the GND voltage including an actual electric
transient.
(6) Short circuit between terminals and erroneous mounting
In order to mount ICs on a set PCB, pay thorough attention to the direction and offset of the ICs. Erroneous mounting can
break down the ICs. Furthermore, if a short circuit occurs due to foreign matters entering between terminals or between
the terminal and the power supply or the GND terminal, the ICs can break down.
(7) Operation in strong electromagnetic field
Be noted that using ICs in the strong electromagnetic field can malfunction them.
(8) Inspection with set PCB
On the inspection with the set PCB, if a capacitor is connected to a low-impedance IC terminal, the IC can suffer stress.
Therefore, be sure to discharge from the set PCB by each process. Furthermore, in order to mount or dismount the set
PCB to/from the jig for the inspection process, be sure to turn OFF the power supply and then mount the set PCB to the
jig. After the completion of the inspection, be sure to turn OFF the power supply and then dismount it from the jig. In
addition, for protection against static electricity, establish a ground for the assembly process and pay thorough attention
to the transportation and the storage of the set PCB.
(9) Input terminals
In terms of the construction of IC, parasitic elements are inevitably formed in relation to potential. The operation of the
parasitic element can cause interference with circuit operation, thus resulting in a malfunction and then breakdown of the
input terminal. Therefore, pay thorough attention not to handle the input terminals, such as to apply to the input terminals
a voltage lower than the GND respectively, so that any parasitic element will operate. Furthermore, do not apply a voltage
to the input terminals when no power supply voltage is applied to the IC. In addition, even if the power supply voltage is
applied, apply to the input terminals a voltage lower than the power supply voltage or within the guaranteed value of
electrical characteristics.
www.rohm.com
? 2013 ROHM Co., Ltd. All rights reserved.
TSZ22111 ? 15 ? 001
18/22
TSZ02201-0E3E0H300290-1-2
08.Mar.2013 Rev.001
相关PDF资料 |
PDF描述 |
|---|---|
| MAX15015AATX+ | IC REG DL BCK/LINEAR 36TQFNEP |
| REC5-4812SRW/H/B | CONV DC/DC 5W 36-72VIN 12VOUT |
| MAX15022ATI+T | IC REG QD BCK/LINEAR SYNC 28TQFN |
| MAX1765EUE+T | IC REG DL BST/LINEAR 16TSSOP |
| REC5-4809SRW/H/B | CONV DC/DC 5W 36-72VIN 09VOUT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| BD651-S | 功能描述:达林顿晶体管 120V 8A NPN RoHS:否 制造商:Texas Instruments 配置:Octal 晶体管极性:NPN 集电极—发射极最大电压 VCEO:50 V 发射极 - 基极电压 VEBO: 集电极—基极电压 VCBO: 最大直流电集电极电流:0.5 A 最大集电极截止电流: 功率耗散: 最大工作温度:+ 150 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-18 封装:Reel |
| BD652 | 功能描述:达林顿晶体管 62.5W PNP Silicon RoHS:否 制造商:Texas Instruments 配置:Octal 晶体管极性:NPN 集电极—发射极最大电压 VCEO:50 V 发射极 - 基极电压 VEBO: 集电极—基极电压 VCBO: 最大直流电集电极电流:0.5 A 最大集电极截止电流: 功率耗散: 最大工作温度:+ 150 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-18 封装:Reel |
| BD6520F | 制造商:ROHM 制造商全称:Rohm 功能描述:Large Current Output Power Management Switch ICs |
| BD6520F_09 | 制造商:ROHM 制造商全称:Rohm 功能描述:Large Current Output Power Management Switch ICs |
| BD6520F_11 | 制造商:ROHM 制造商全称:Rohm 功能描述:Load Switch ICs for Portable Equipment |
发布紧急采购，3分钟左右您将得到回复。