- 您现在的位置：买卖IC网 > Datasheet目录315 > BD6581GU-E2 (Rohm Semiconductor)IC LED DVR WHT BCKLGHT VCSP85H2 Datasheet资料下载
参数资料
| 型号： | BD6581GU-E2 |
| 厂商： | Rohm Semiconductor |
| 文件页数： | 13/35页 |
| 文件大小： | 0K |
| 描述： | IC LED DVR WHT BCKLGHT VCSP85H2 |
| 标准包装： | 3,000 |
| 拓扑： | PWM，升压（升压） |
| 输出数： | 6 |
| 内部驱动器： | 是 |
| 类型 - 主要： | 背光 |
| 类型 - 次要： | 白色 LED |
| 频率： | 800kHz ~ 1.2MHz |
| 电源电压： | 2.7 V ~ 22 V |
| 输出电压： | 44.7 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 23-VFBGA，CSPBGA |
| 供应商设备封装： | VCSP85H2 |
| 包装： | 带卷 (TR) |
| 工作温度： | -30°C ~ 85°C |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页当前第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页
BD6581GU
Datasheet
4) External SBD open detect and over voltage protection
BD6581GU has over boost protection by external SBD open and over voltage protection. It detects VDET voltage and is
stopped output Tr in abnormal condition. Details are as shown below.
? External SBD open detect
In the case of external SBD is not connected to IC, the coil or external Tr may be destructed. Therefore, at such an
error as VOUT becoming 0.1V or below, the Under Detector shown in the figure works, and turns off the output Tr, and
prevents the coil and the IC from being destructed.
And the IC changes from activation into non-activation, and current does not flow to the coil (0mA).
? Over voltage protection
At such an error of output open as the output DC/DC and the LED is not connected to IC, the DC/DC will boost too
much and the VDET terminal exceed the absolute maximum ratings, and may destruct the IC. Therefore, when VDET
becomes sensing voltage or higher, the over voltage limit works, and turns off the output Tr, and the pressure up made
stop.
At this moment, the IC changes from activation into non-activation, and the output voltage goes down slowly. And,
when the output voltage becomes the hysteresis of the over voltage limit or below, the output voltage pressure up to
sensing voltage once again and unless the application error is recovered, this operation is repeated.
5) Thermal shut down
BD6581GU has thermal shut down function.
The thermal shut down works at 175 ° C or higher, and the IC changes from activation into non-activation. Because
non-activation is different from RSTB=L, it doesn’t’ be reset inside IC. Moreover, even if thermal shut down function works,
soft start, FAILSEL, selection the number of LED lines of the current driver and starting current setting at PWMDRV=L
related RSTB are hold.
6) Over Current Limit
Over current flows the current detection resistor that is connected to switching transistor source and between GND,
SENSP pin voltage turns more than detection voltage, over current protection is operating and it is prevented from
flowing more than detection current by reducing ON duty of switching Tr without stopping boost.
As over current detector of BD6581GU is detected peak current, current more than over current setting value does not
flow.
And, over current value can decide freely by changing over current detection voltage.
<Derivation sequence of detection resistor>
Detection resistor =Over current detection voltage / Over current setting value
TYP value of over current detection voltage is 100mV, MIN = 70mV and MAX = 130mV and after the current value
which was necessary for the normal operation was decided, detection resistor is derived by using MIN value of over
current detection value.
For example, detection resistor when necessary current value was set at 1A is given as shown below.
Detection resistor =70mV / 1A = 70m ?
MAX current dispersion of this detection resistor value is
MAX current = 130mV / 70m ? = 1.86A
<The estimate of the current value which need for the normal operation >
As over current detector of BD6581GU is detected the peak current, it have to estimate peak current to flow to the coil
by operating condition.
In case of, ○ Supply voltage of coil = VIN
○ Switching frequency = fsw
○ Output voltage = VOUT
○ Inductance value of coil = L
MIN=0.8MHz, Typ=1MHz, MAX=1.2MHz
○ Total LED current = IOUT
○ Average current of coil = Iave ○ Peak current of coil = Ipeak
○ Efficiency = eff (Please set up having margin, it refers to data on page 7.)
○ ON time of switching transistor = Ton
Ipeak = (VIN / L) x (1 / fsw) x (1-(VIN / VOUT))
Iave=(VOUT x IOUT / VIN) / eff
Ton=(Iave x (1-VIN/VOUT) x (1/fsw) x (L/VIN) x 2) 1/2
Each current is calculated.
As peak current varies according to whether there is the direct current superposed, the next is decided.
(1-VIN/VOUT) x (1/fsw) < Ton →
(1-VIN/VOUT) x (1/fsw) > Ton →
peak current = Ipeak /2 + Iave
peak current = Ipeak
(Example 1)
In case of, VIN=6.0V, L=4.7μH, fsw=1MHz, VOUT=39V, IOUT=80mA, Efficiency=85%
Ipeak = (6.0V / 4.7μH) x (1 / 1MHz) x (1-(6.0V / 39V)) =1.08A
Iave = (39V x 80mA / 6.0V) / 85% = 0.61A
Ton = (0.61A x (1-6.0V / 39V) x (1 / 1MHz) x ( 4.7μH /6.0V) x 2) 1/2 = 0.90μs
(1-VIN/VOUT) x (1/fsw)=0.85μs < Ton
Peak current = 1.08A/2+0.61A = 1.15A
www.rohm.com
? 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111 ? 15 ? 001
13/32
TSZ02201-0G3G0C400170-1-2
03.Dec.2012 Rev.001
相关PDF资料 |
PDF描述 |
|---|---|
| BD6583MUV-AE2 | IC LED DRIVER WHIT BCKLGT 24VQFN |
| BD6586MUV-E2 | IC LED DRVR WHITE BCKLGT 24-VQFN |
| BD6592MUV-E2 | IC LED DRVR WHITE BCKLGT 24-VQFN |
| BD7844AEFV-E2 | IC LED DISPLAY DVR 5V 28-HTSSOP |
| BD8105FV-E2 | IC LED DVR SERIAL PAR 20-SSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| BD6583MUV | 制造商:ROHM 制造商全称:Rohm 功能描述:Step-up DC/DC converter for medium size LCD panel |
| BD6583MUV-A | 制造商:ROHM 制造商全称:Rohm 功能描述:White Backlight LED Driver for Medium to Large LCD Panels (Switching Regulator Type) |
| BD6583MUV-A_11 | 制造商:ROHM 制造商全称:Rohm 功能描述:White Backlight LED Driver for Medium to Large LCD Panels (Switching Regulator Type) |
| BD6583MUV-AE2 | 功能描述:IC LED DRIVER WHIT BCKLGT 24VQFN RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 标准包装:60 系列:- 恒定电流:- 恒定电压:- 拓扑:线性（LDO），PWM，升压（升压） 输出数:8 内部驱动器:是 类型 - 主要:背光 类型 - 次要:RGB，白色 LED 频率:500kHz ~ 1.5MHz 电源电压:4.75 V ~ 26 V 输出电压:45V 安装类型:* 封装/外壳:* 供应商设备封装:* 包装:* 工作温度:-40°C ~ 85°C |
| BD6583MUV-E2 | 功能描述:LED照明驱动器 72 LEDs 2.7-22V 43V Max Out 25mA Out RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
发布紧急采购，3分钟左右您将得到回复。