- 您现在的位置：买卖IC网 > Datasheet目录315 > BD6581GU-E2 (Rohm Semiconductor)IC LED DVR WHT BCKLGHT VCSP85H2 Datasheet资料下载
参数资料
| 型号： | BD6581GU-E2 |
| 厂商： | Rohm Semiconductor |
| 文件页数： | 18/35页 |
| 文件大小： | 0K |
| 描述： | IC LED DVR WHT BCKLGHT VCSP85H2 |
| 标准包装： | 3,000 |
| 拓扑： | PWM，升压（升压） |
| 输出数： | 6 |
| 内部驱动器： | 是 |
| 类型 - 主要： | 背光 |
| 类型 - 次要： | 白色 LED |
| 频率： | 800kHz ~ 1.2MHz |
| 电源电压： | 2.7 V ~ 22 V |
| 输出电压： | 44.7 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 23-VFBGA，CSPBGA |
| 供应商设备封装： | VCSP85H2 |
| 包装： | 带卷 (TR) |
| 工作温度： | -30°C ~ 85°C |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页当前第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页
BD6581GU
Datasheet
● Brightness Control
There are two dimming method is available, first method is analog dimming that apply analog voltage to ISET terminal, and
second method is PWM control via digital dimming of PWMPOW or PWMDRV. Because each method has the different
merit, please choose a suitable method for the application of use.
Two techniques can be used as digital dimming by the PWM control One is PWM control of current driver, the other is PWM
control of power control.
As these two characteristics are shown in the below, selects to PWM control process comply with application.
? Efficiency emphasis in the low brightness which has an influence with the battery life
? LED current dispersion emphasis in the PWM brightness control
(Reference)
→ 2) Power control PWM control
→ 1) Current driver PWM control
PWM regulation process
Current driver
Power control
Efficiency of LED current 0.5mA
(PWM Duty=2.5%)
70%
93%
PWM frequency 200Hz
Limit dispersion capability of low duty
0.2%
0.5%
1) Current driver PWM control is controlled by providing PWM signal to PWMDRV, as it is shown Figure 41.
The current set up with ISETH is chosen as the Hi section of PWMDRV and the current is off as the Lo section. Therefore,
the average LED current is increasing in proportion to duty cycle of PWMDRV signal. This method that it lets internal
circuit and DC/DC to work, because it becomes to switch the driver, the current tolerance is a few when the PWM
brightness is adjusted, it makes it possible to brightness control until 50μs (MIN1% at 200Hz). And, don't use for the
brightness control, because effect of ISETH, ISETL changeover is big under 50μs ON time and under 50μs OFF time.
Typical PWM frequency is 100Hz to 10kHz. When RSTB sets H → L, so the starting current may be effective, after
RSTB sets L → H, it becomes PWM of the starting current and PWM of ISETH setting current to PWM two times.
PWMDRV
LED current
Coil current
IC’s active current
ON
ON
ON
OFF
OFF
OFF
ON
Figure 37. PWM modulated light by PWM DRV Pin
2) Power control PWM control is controlled by providing PWM signal to PWMPOW, as it is shown Figure 43. The current
setting set up with PWMDRV logic is chosen as the Hi section and the current is off as the Lo section. Therefore, the
average LED current is increasing in proportion to duty cycle of PWMPOW signal. This method is, because IC can be
power-off at off-time, the consumption current can be suppress, and the high efficiency can be available, so it makes it
possible to brightness control until 50μs (MIN1% at 200Hz). And, don't use for the brightness control, because effect of
power ON/OFF time changeover is big under 50μs ON time and under 50μs OFF time.
Typical PWM frequency is 100Hz to 1kHz. Also, PWM can't control RSTB and PWMPOW at the same time.
After RSTB sets H, control PWM only PWMPOW.
PWMPOW
LED current
Coil current
IC’s active current
ON
ON
ON
ON
OFF
OFF
OFF
OFF
Figure 38. PWM modulated by PWM Pow Pin
www.rohm.com
? 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111 ? 15 ? 001
18/32
TSZ02201-0G3G0C400170-1-2
03.Dec.2012 Rev.001
相关PDF资料 |
PDF描述 |
|---|---|
| BD6583MUV-AE2 | IC LED DRIVER WHIT BCKLGT 24VQFN |
| BD6586MUV-E2 | IC LED DRVR WHITE BCKLGT 24-VQFN |
| BD6592MUV-E2 | IC LED DRVR WHITE BCKLGT 24-VQFN |
| BD7844AEFV-E2 | IC LED DISPLAY DVR 5V 28-HTSSOP |
| BD8105FV-E2 | IC LED DVR SERIAL PAR 20-SSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| BD6583MUV | 制造商:ROHM 制造商全称:Rohm 功能描述:Step-up DC/DC converter for medium size LCD panel |
| BD6583MUV-A | 制造商:ROHM 制造商全称:Rohm 功能描述:White Backlight LED Driver for Medium to Large LCD Panels (Switching Regulator Type) |
| BD6583MUV-A_11 | 制造商:ROHM 制造商全称:Rohm 功能描述:White Backlight LED Driver for Medium to Large LCD Panels (Switching Regulator Type) |
| BD6583MUV-AE2 | 功能描述:IC LED DRIVER WHIT BCKLGT 24VQFN RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 标准包装:60 系列:- 恒定电流:- 恒定电压:- 拓扑:线性（LDO），PWM，升压（升压） 输出数:8 内部驱动器:是 类型 - 主要:背光 类型 - 次要:RGB，白色 LED 频率:500kHz ~ 1.5MHz 电源电压:4.75 V ~ 26 V 输出电压:45V 安装类型:* 封装/外壳:* 供应商设备封装:* 包装:* 工作温度:-40°C ~ 85°C |
| BD6583MUV-E2 | 功能描述:LED照明驱动器 72 LEDs 2.7-22V 43V Max Out 25mA Out RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
发布紧急采购，3分钟左右您将得到回复。