参数资料
型号: BD6592MUV-E2
厂商: Rohm Semiconductor
文件页数: 14/34页
文件大小: 0K
描述: IC LED DRVR WHITE BCKLGT 24-VQFN
标准包装: 1
拓扑: PWM,升压(升压)
输出数: 6
内部驱动器:
类型 - 主要: 背光
类型 - 次要: 白色 LED
频率: 800kHz ~ 1.2MHz
电源电压: 2.7 V ~ 22 V
输出电压: 43V
安装类型: 表面贴装
封装/外壳: 24-VFQFN 裸露焊盘
供应商设备封装: VQFN024V4040
包装: 标准包装
工作温度: -30°C ~ 85°C
产品目录页面: 1372 (CN2011-ZH PDF)
其它名称: BD6592MUV-E2DKR
BD6592MUV
(Example 1)
In case of, VIN=6.5V, L=4.7μH, fsw=1MHz, VOUT=39V, IOUT=80mA, Efficiency=85%
Ipeak = (6.5V / 4.7μH) × (1 / 1MHz) × (1-(6.5V / 39V)) =1.08A
Iave = (39V × 80mA / 6.0V) / 85% = 0.61A
Ton = (0.61A × (1-6.0V / 39V) × (1 / 1MHz) × ( 4.7μH /6.0V) × 2) 1/2 = 0.90μs
(1-VIN/VOUT) × (1/fsw) =0.85μs < Ton
Peak current = 1.08A/2+0.61A = 1.15A
(Example 2)
In case of, VIN=12.0V, L=4.7μH, fsw=1MHz, VOUT=39V, IOUT=80mA, Efficiency=85%
Ipeak = (12.0V / 4.7μH) × (1 / 1MHz) × (1-(12V / 39V)) =1.77A
Datasheet
Ton = (0.31A × (1-12 V / 39V) × (1 / 1MHz) × ( 4.7μH /12 V) × 2)
Iave = (39V x 80mA / 12.0V) / 85% = 0.31A
1/2
= 0.41μs
(1-VIN/VOUT) × (1/fsw) =0.69μs > Ton
Peak current = 12V/4.7μH × 0.41μs = 1.05A
When too large current is set, output overshoot is caused, be careful enough because it is led to break down of the IC in
case of the worst.
● Operating of the Application Deficiency
1) When 1 LED or 1parallel OPEN during the operating
In case of FAILSEL=L, the LED parallel which became OPEN isn't lighting, but other LED parallel is lighting. At that time,
output boosts up to the over voltage protection voltage 44.7V so that LED terminal may be 0V or it boost to the output voltage
that LED terminal voltage becomes LED terminal over voltage protection 11.5V or it becomes the output voltage
restricted by the over current limit.In case of FAILSEL=H, boost stops when LED becomes OPEN and all LED turns off
the lights.
2) When LED short-circuited in the plural
In case of FAILSEL=L, all LED is turned on unless LED terminal voltage is LED terminal over voltage protection of more than 11.5V.
When it was more than 11.5V only the line which short-circuited is turned on normally and LED current of other lines fall
or turn off the lights. In case of FAILSEL=H, boost stops at more than 11.5V and all LED turns off the lights.
3) When Schottky diode came off
Regardless of FAILSEL, all LED isn't turned on. Also, IC and a switching transistor aren't destroyed because boost
operating stops by the Schottky diode coming off protected function.
4) When over current detection resistor came off
Regardless of FAILSEL, all LED isn't turned on. Because the resistance of 100k ? is between SENSP and SENSN
terminal, over current protection works instantly and LED current can't be flow.
● Control Signal Input Timing
2.7V 5V
0V
VBAT
1
2
Min. 100μs
5V
VBAT
RSTB
PWMPOW
3
5V
220 ?
PIN
Rin
PWMDRV
GND
VREG
DC/DC VOUT
Figure 33. Control signal timing
Figure 34. Voltage with a control sign higher than VBAT
Example corresponding to application of conditions
In case you input control signs, such as RSTB, PWMPOW, and PWMDRV, in the condition that the standup of supply
voltage (VBAT) is not completed, be careful of the following point.
① Input each control signal after VBAT exceeds 2.7V.
② Please do not input each control sign until VBAT exceeds HI voltage of RSTB, PWMPOW, and PWMDRV.
③ When you input RSTB during the standup of VBAT and HI voltage is inputted into PWMPOW, please give the standup
time to stable voltage as Min.100μs 2.7V of VBAT.
There is no timing limitation at each input signal of RSTB, PWMPOW and PWMDRV.
If each control sign changes into a condition lower than VBAT in (1) and (2), it goes via the ESD custody diode by the side
of VBAT of each terminal. A power supply is supplied to VBAT and there is a possibility of malfunctioning. Moreover, when
the entrance current to the terminal exceeds 50mA, it has possibility to damage the LSI. In order to avoid this condition, as
shown in the above figure, please insert about 220ohm in a signal line, and apply current qualification. Please confirm an
internal pull down resistor in the block diagram and electrical property of Page.4.
www.rohm.com
? 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111 ? 15 ? 001
14 / 31
TSZ02201-0G3G0C400210-1-2
21.Dec.2012 Rev.001
相关PDF资料
PDF描述
BD7844AEFV-E2 IC LED DISPLAY DVR 5V 28-HTSSOP
BD8105FV-E2 IC LED DVR SERIAL PAR 20-SSOP
BD8112EFV-ME2 IC LED DRIVER 24-VSSOP
BD8119FM-ME2 IC WHITE LED DVR PWM 28-HSOP
BD82103GWL-E2 IC LED DRVR WHITE BCKLGT 11-UCSP
相关代理商/技术参数
参数描述
BD65B60GWL-E2 功能描述:LED 驱动器 IC 2 输出 DC DC 稳压器 升压(升压) PWM 调光 25mA UCSP50L1 制造商:rohm semiconductor 系列:- 包装:剪切带(CT) 零件状态:有效 类型:DC DC 稳压器 拓扑:升压(升压) 内部开关:是 输出数:2 电压 - 供电(最低):2.7V 电压 -?供电(最高):5.5V 电压 - 输出:28.5V 电流 - 输出/通道:25mA 频率:600kHz ~ 1.1MHz 调光:PWM 应用:背光 工作温度:-40°C ~ 85°C(TA) 安装类型:表面贴装 封装/外壳:12-UFBGA,CSPBGA 供应商器件封装:UCSP50L1 标准包装:1
BD65D00MUV-E2 功能描述:LED 驱动器 IC 4 输出 DC DC 稳压器 升压(升压) 模拟,PWM 调光 100mA VQFN028V5050 制造商:rohm semiconductor 系列:- 包装:剪切带(CT) 零件状态:有效 类型:DC DC 稳压器 拓扑:升压(升压) 内部开关:是 输出数:4 电压 - 供电(最低):4.5V 电压 -?供电(最高):27V 电压 - 输出:41V 电流 - 输出/通道:100mA 频率:1.25MHz 调光:模拟,PWM 应用:背光 工作温度:-40°C ~ 85°C(TA) 安装类型:表面贴装 封装/外壳:28-VFQFN 裸露焊盘 供应商器件封装:VQFN028V5050 标准包装:1
BD6603KVT 制造商:ROHM 制造商全称:Rohm 功能描述:5ch Sensorless System Motor Driver for MD
BD6603KVT_11 制造商:ROHM 制造商全称:Rohm 功能描述:Silicon Monolithic Integrated Circuit
BD6607KN 制造商:ROHM 制造商全称:Rohm 功能描述:System Motor Driver for Portable MD