参数资料
| 型号： | BD8157EFV-E2 |
| 厂商： | Rohm Semiconductor |
| 文件页数： | 9/20页 |
| 文件大小： | 0K |
| 描述： | IC POWER SUP 1-CH HTSSOP-B20 |
| 标准包装： | 2,500 |
| 应用： | TFT-LCD 面板：伽玛缓冲器，VCOM 驱动器 |
| 电流 - 电源： | 1.2mA |
| 电源电压： | 2.1 V ~ 4 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-VSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 20-HTSSOP-B |
| 包装： | 带卷 (TR) |
BD8151EFV, BD8157EFV
Technical Note
● Selecting Application Components
(1) Setting the output L constant
The coil L to use for output is decided by the rating current I LR and input current maximum value I INMAX of the coil.
I INMAX + ? I L should not reach
Vcc
IL
the rating value level
L
I L
INMAX
I
current
t
average
Co
Vo
Fig. 29 Coil Current Waveform
Fig. 30 Output Application Circuit Diagram
Adjust so that I INMAX + ? I L does not reach the rating current value I LR . At this time, ? I L can be obtained by the following
equation.
Vcc ?
?
? I L =
1 Vo-Vcc 1
L Vcc f
[A] Where, f is the switching frequency.
Set with sufficient margin because the coil L value may have the dispersion of approx. ? 30%. If the coil current exceeds
the rating current I LR of the coil, it may damage the IC internal element.
BD8157EFV uses the current mode DC/DC converter control and has the optimized design at the coil value. The following
coil values are recommended from the aspects of power efficiency, response and safety. When the coil out of this range is
selected, the stable continual operation is not guaranteed such as the switching waveform becomes irregular. Please pay
attention to it.
Switching frequency: L = 10 μH to 22 μH at 600 kHz
Switching frequency: L = 4.7 μH to 15 μH at 1,200 kHz
(2) Setting the output capacitor
For the capacitor C to use for the output, select the capacitor which has the larger value in the ripple voltage V PP allowance
value and the drop voltage allowance value at the time of sudden load change. Output ripple voltage is decided by the
following equation.
?
? (I LMAX -
? V PP
= I LMAX × R ESR +
1 Vcc ? I L
fCo Vo 2
) [V] Where, f is the switching frequency.
Perform setting so that the voltage is within the allowable ripple voltage range.
For the drop voltage during sudden load change; V DR , please perform the rough calculation by the following equation.
VDR
=
? I
Co
? 10 μ sec
[V]
However, 10 μs is the rough calculation value of the DC/DC response speed. Please set the capacitance considering the
sufficient margin so that these two values are within the standard value range.
(3) Selecting the input capacitor
Since the peak current flows between the input and output at the DC/DC converter, a capacitor is required to install at the
input side. For this reason, the low ESR capacitor is recommended as an input capacitor which has the value more than
10 μF and less than 100 m ? . If a capacitor out of this range is selected, the excessive ripple voltage is superposed on the
input voltage, accordingly it may cause the malfunction of IC.
However these conditions may vary according to the load current, input voltage, output voltage, inductance and switching
frequency. Be sure to perform the margin check using the actual product.
www.rohm.com
? 2009 ROHM Co., Ltd. All rights reserved.
9/17
2009.07 - Rev.B
相关PDF资料 |
PDF描述 |
|---|---|
| BD8314NUV-E2 | IC REG BOOST ADJ 2.5A SON10 |
| BD8621EFV-E2 | IC PWR SUPP 3A W/FET HTSSOP-B20 |
| BD8622EFV-E2 | IC PWR SUPP 3A W/FET HTSSOP-B20 |
| BD8629FS-E2 | IC PWR SUPP 2A W/FET SSOP-A16 |
| BD8643FV-E2 | IC REG BUCK SYNC ADJ 3A 20SSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| BD8158FVM | 制造商:ROHM 制造商全称:Rohm 功能描述:TFT-LCD Bias Boost Converter |
| BD8158FVM-TR | 功能描述:直流/直流开关调节器 1-CH SOURCE OUTPUT POWER SUPPLY RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| BD8158FVM-TR-CUT TAPE | 制造商:ROHM 功能描述:BD Series 2.1 to 4 V 1200 kHz Boost SMT Switching Regulator - MSOP-8 |
| BD816 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:TRANSISTOR | BJT | PNP | 60V V(BR)CEO | 2A I(C) | TO-202 |
| BD8160AEFV | 制造商:ROHM 制造商全称:Rohm 功能描述:12V Input Multi-channel System Power Supply IC |
发布紧急采购，3分钟左右您将得到回复。