参数资料
| 型号： | BD8966FVM-TR |
| 厂商： | Rohm Semiconductor |
| 文件页数： | 16/19页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK SYNC ADJ 0.8A MSOP8 |
| 标准包装： | 3,000 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 1 V ~ 2.5 V |
| 输入电压： | 4 V ~ 5.5 V |
| PWM 型： | 电流模式 |
| 频率 - 开关： | 1MHz |
| 电流 - 输出： | 800mA |
| 同步整流器： | 是 |
| 工作温度： | -25°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-VSSOP，8-MSOP（0.110"，2.80mm 宽） |
| 包装： | 带卷 (TR) |
| 供应商设备封装： | 8-MSOP |
BD8966FVM
Datasheet
This is a monolithic IC with P isolation between P-substrate and each element as illustrated below. This P-layer and
● Operational Notes
1. Absolute Maximum Ratings
While utmost care is taken to quality control of this product, any application that may exceed some of the absolute
maximum ratings including the voltage applied and the operating temperature range may result in breakage. If broken,
short-mode or open-mode may not be identified. So if it is expected to encounter with special mode that may exceed the
absolute maximum ratings, it is requested to take necessary safety measures physically including insertion of fuses.
2. Electrical potential at GND
GND must be designed to have the lowest electrical potential In any operating conditions.
3. Short-circuiting between terminals, and mismounting
When mounting to pc board, care must be taken to avoid mistake in its orientation and alignment. Failure to do so may
result in IC breakdown. Short-circuiting due to foreign matters entered between output terminals, or between output and
power supply or GND may also cause breakdown.
4. Operation in Strong electromagnetic field
Be noted that using the IC in the strong electromagnetic radiation can cause operation failures.
5. Thermal shutdown protection circuit
Thermal shutdown protection circuit is the circuit designed to isolate the IC from thermal runaway, and not intended to
protect and guarantee the IC. So, the IC the thermal shutdown protection circuit of which is once activated should not
be used thereafter for any operation originally intended.
6. Inspection with the IC set to a pc board
If a capacitor must be connected to the pin of lower impedance during inspection with the IC set to a pc board, the
capacitor must be discharged after each process to avoid stress to the IC. For electrostatic protection, provide proper
grounding to assembling processes with special care taken in handling and storage. When connecting to jigs in the
inspection process, be sure to turn OFF the power supply before it is connected and removed.
7. Input to IC terminals
+
the N-layer of each element form a P-N junction, and various parasitic element are formed.
If a resistor is joined to a transistor terminal as shown in Fig 34.
○ P-N junction works as a parasitic diode if the following relationship is satisfied; GND>Terminal A (at resistor side), or
GND>Terminal B (at transistor side); and
○ if GND>Terminal B (at NPN transistor side),
a parasitic NPN transistor is activated by N-layer of other element adjacent to the above-mentioned parasitic diode.
The structure of the IC inevitably forms parasitic elements, the activation of which may cause interference among circuits, and/or
malfunctions contributing to breakdown. It is therefore requested to take care not to use the device in such manner that the
voltage lower than GND (at P-substrate) may be applied to the input terminal, which may result in activation of parasitic elements.
Fig.34 Simplified structure of monorisic IC
8. Ground wiring pattern
If small-signal GND and large-current GND are provided, It will be recommended to separate the large-current GND
pattern from the small-signal GND pattern and establish a single ground at the reference point of the set PCB so that
resistance to the wiring pattern and voltage fluctuations due to a large current will cause no fluctuations in voltages of the
small-signal GND. Pay attention not to cause fluctuations in the GND wiring pattern of external parts as well.
9. Selection of inductor
It is recommended to use an inductor with a series resistance element (DCR) 0.1 Ω or less. Note that use of a high DCR
inductor will cause an inductor loss, resulting in decreased output voltage. Should this condition continue for a specified
period (soft start time + timer latch time), output short circuit protection will be activated and output will be latched OFF.
When using an inductor over 0.1Ω, be careful to ensure adequate margins for variation between external devices and this
IC, including transient as well as static characteristics. Furthermore, in any case, it is recommended to start up the output
with EN after supply voltage is within operation range.
Status of this document
The Japanese version of this document is formal specification. A customer may use this translation version only for a reference
to help reading the formal version.
If there are any differences in translation version of this document formal version takes priority
www.rohm.com
? ROHM Co., Ltd. All rights reserved.
TSZ22111 ? 15 ? 001
16/17
TSZ02201-0J3J0AJ00060-1-2
02.MAR.2012. Rev.001
相关PDF资料 |
PDF描述 |
|---|---|
| BD91361MUV-E2 | IC REG BUCK SYNC ADJ 4A 20VQFN |
| BD9137MUV-E2 | IC REG BUCK SYNC ADJ 4A 20VQFN |
| BD9139MUV-E2 | IC REG BUCK SYNC ADJ 3A 16VQFN |
| BD9140MUV-E2 | IC REG BUCK SYNC ADJ 2A VQFN020 |
| BD9300F-E2 | IC REG CTRLR BST INV PWM 14-SOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| BD8966FVM--TR | 制造商:ROHM 制造商全称:Rohm 功能描述:Low Noise High Efficiency Step-down Switching Regulator with Built-in Power MOSFET |
| BD8967FVM | 制造商:ROHM 制造商全称:Rohm 功能描述:4.5V to 5.5V, 0.8A 1ch Synchronous Buck Converter integrated FET |
| BD8967FVM_12 | 制造商:ROHM 制造商全称:Rohm 功能描述:4.5V to 5.5V, 0.8A 1ch Synchronous Buck Converter integrated FET |
| BD8967FVM-TR | 制造商:ROHM Semiconductor 功能描述:CONV DC-DC SINGLE STEP DOWN T/R - Tape and Reel 制造商:ROHM Semiconductor 功能描述:IC REG BUCK SYNC 3.3V .8A 8-MSOP 制造商:ROHM Semiconductor 功能描述:CONV SINGLE STPDWN DC-DC |
| BD896A | 功能描述:达林顿晶体管 70W PNP Silicon RoHS:否 制造商:Texas Instruments 配置:Octal 晶体管极性:NPN 集电极—发射极最大电压 VCEO:50 V 发射极 - 基极电压 VEBO: 集电极—基极电压 VCBO: 最大直流电集电极电流:0.5 A 最大集电极截止电流: 功率耗散: 最大工作温度:+ 150 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-18 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。