参数资料
| 型号： | BD9305AFVM-TR |
| 厂商： | Rohm Semiconductor |
| 文件页数： | 13/15页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM 8-MSOP |
| 标准包装： | 1 |
| PWM 型： | 控制器 |
| 输出数： | 1 |
| 频率 - 最大： | 800kHz |
| 占空比： | 100% |
| 电源电压： | 4.2 V ~ 18 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 8-VSSOP，8-MSOP（0.110"，2.80mm 宽） |
| 包装： | 标准包装 |
| 其它名称： | BD9305AFVM-DKR BD9305AFVM-DKR-ND BD9305AFVMDKR |
BD9306AFVM, BD9305AFVM
Technical Note
? Notes for use
1) Absolute maximum ratings
Use of the IC in excess of absolute maximum ratings such as the applied voltage or operating temperature range may
result in IC damage. Assumptions should not be made regarding the state of the IC (short mode or open mode) when such
damage is suffered. A physical safety measure such as a fuse should be implemented when use of the IC in a special
mode where the absolute maximum ratings may be exceeded is anticipated.
2) GND potential
Ensure a minimum GND pin potential in all operating conditions.
3) Setting of heat
Use a thermal design that allows for a sufficient margin in light of the power dissipation (Pd) in actual operating conditions.
4) Pin short and mistake fitting
Use caution when orienting and positioning the IC for mounting on printed circuit boards. Improper mounting may result in
damage to the IC. Shorts between output pins or between output pins and the power supply and GND pins caused by the
presence of a foreign object may result in damage to the IC.
5) Actions in strong magnetic field
Use caution when using the IC in the presence of a strong magnetic field as doing so may cause the IC to malfunction.
6) Testing on application boards
When testing the IC on an application board, connecting a capacitor to a pin with low impedance subjects the IC to stress.
Always discharge capacitors after each process or step. Ground the IC during assembly steps as an antistatic measure,
and use similar caution when transporting or storing the IC. Always turn the IC's power supply off before connecting it to or
removing it from a jig or fixture during the inspection process.
7) Ground wiring patterns
When using both small signal and large current GND patterns, it is recommended to isolate the two ground patterns,
placing a single ground point at the application's reference point so that the pattern wiring resistance and voltage
variations caused by large currents do not cause variations in the small signal ground voltage. Be careful not to change the
GND wiring patterns of any external components.
8) Regarding input pin of the IC
This monolithic IC contains P+ isolation and P substrate layers between adjacent elements in order to keep them isolated.
P/N junctions are formed at the intersection of these P layers with the N layers of other elements to create a variety of
parasitic elements.For example, when the resistors and transistors are connected to the pins shown as follows, a parasitic
diode or a transistor operates by inverting the pin voltage and GND voltage.
The formation of parasitic elements as a result of the relationships of the potentials of different pins is an inevitable result
of the IC's architecture. The operation of parasitic elements can cause interference with circuit operation as well as IC
malfunction and damage. For these reasons, it is necessary to use caution so that the IC is not used in a way that will
trigger the operation of parasitic elements such as by the application of voltages lower than the GND (P substrate) voltage
to input and output pins.
Example of a SimpleMonolithic IC Architecture
Resistor
Transistor (NPN)
(Pin B)
(Pin A)
(Pin B)
C
B
E
B
C
E
N
GND
GND
N
P+
N
P
P+
N
N
P+
N
P
P+
N
(Pin A)
Parasitic
elements
P
Parasitic elements
P substrate
GND
Parasitic elements
GND
Parasitic
elements
GND
Fig. 33
9) Overcurrent protection circuits
An overcurrent protection circuit designed according to the output current is incorporated for the prevention of IC damage
that may result in the event of load shorting. This protection circuit is effective in preventing damage due to sudden and
unexpected accidents. However, the IC should not be used in applications characterized by the continuous operation or
transitioning of the protection circuits. At the time of thermal designing, keep in mind that the current capacity has negative
characteristics to temperatures.
www.rohm.com
? 2009 ROHM Co., Ltd. All rights reserved.
13/14
2009.05 - Rev.A
相关PDF资料 |
PDF描述 |
|---|---|
| BD9328EFJ-E2 | IC REG BUCK SYNC ADJ 2A 8HTSOP |
| BD9329AEFJ-E2 | IC REG BUCK SYNC ADJ 3A 8HTSOP |
| BD9533EKN-E2 | IC REG SW VAR SOFT START 20-HQFN |
| BD95513MUV-E2 | IC REG BUCK ADJ 3A 32VQFN |
| BD9701T-V5 | IC REG BUCK ADJ 1.5A TO220FP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| BD9306AFVM | 制造商:ROHM 制造商全称:Rohm 功能描述:Single-output Step-up,High-efficiency Switching Regulator(Controller Type) |
| BD9306AFVM-TR | 功能描述:直流/直流开关调节器 4.2-18V 100-800kHz 1 Chan Step-Up RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| BD9322EFJ | 功能描述:IC REG BUCK SYNC ADJ 2A 8HTSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 产品培训模块:High Efficiency Current Mode Switching Regulators CMOS LDO Regulators 特色产品:BD91x Series Step-Down Regulators 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:两者兼有 输出数:2 输出电压:3.3V，0.8 V ~ 2.5 V 输入电压:4.5 V ~ 5.5 V PWM 型:电流模式 频率 - 开关:1MHz 电流 - 输出:1.5A 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:20-VFQFN 裸露焊盘 包装:带卷 (TR) 供应商设备封装:VQFN020V4040 产品目录页面:1373 (CN2011-ZH PDF) 其它名称:BD9152MUV-E2TR |
| BD9322EFJ-E2 | 功能描述:直流/直流开关调节器 4.75-18V; 380kHz; 2A 1Ch Stp-Dwn w/MOSFET RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| BD9323EFJ-E2 | 功能描述:直流/直流开关调节器 4.75-18V; 380kHz; 3A 1Ch Stp-Dwn w/MOSFET RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
发布紧急采购，3分钟左右您将得到回复。