- 您现在的位置：买卖IC网 > Datasheet目录397 > BH1621FVC-TR (Rohm Semiconductor)IC AMBIENT LIGHT SENSOR 5WSOF Datasheet资料下载
参数资料
| 型号： | BH1621FVC-TR |
| 厂商： | Rohm Semiconductor |
| 文件页数： | 5/12页 |
| 文件大小： | 0K |
| 描述： | IC AMBIENT LIGHT SENSOR 5WSOF |
| 标准包装： | 3,000 |
| 系列： | * |
| 带接近传感器： | 无 |
| 波长： | 560nm |
| 电源电压： | 2.4 V ~ 5.5 V |
| 电流 - 暗（标准）： | 200nA（最小值） |
| 电流 - 光（典型值）： | 60µA |
| 输出类型： | 模拟 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | SOT-665 |
| 包装： | 带卷 (TR) |
BH1621FVC
● External parts Setting
1) Gain setting of BH1621FVC
Please select the best gain controlled by 3 and 4pin based on the required illuminance range.
The reference is as follows.
Technical Note
Illuminance detection range [lx]
~1000
~50,000
Gain Mode
H-Gain Mode
L-Gain Mode
Viout= 0.60 x 10 x Ev x R1
R1 = Viout/(0.60 x 10 x Ev)
= 2 /(0.60 x 10 x 500) = 6667[ ? ]
This device will be mounted under the optical window in actual designing. Therefore, there is a possibility that the
illuminace to ALS ( Ambient Light Sensor ) will be less than the illuminance on the final product surface.
Please consider the attenuation of light through the optical window.
It is possible to detect illuminance up to about 5000 lx even in the H-Gain mode. However, the maximum output current
is about 3mA in this case. If you want to minimize consumption current, please use the L-Gain mode as much as possible.
Please set output resistance value ( R1 ) within the range of 1 k Ω ~ 1M Ω which needs to be smaller than the input
impedance of the next circuit.
2) Approximate formula of IOUT output voltage in each Gain Mode
(1) H-Gain mode
The output voltage is calculated as below.
-6
Viout is IOUT output voltage [V]. Ev is an illuminance of the ALS surface [lx].
R1 is IOUT output resistor[ ? ].
( For example ) In case you want to convert the illuminance value up to 500 lx by ADC.
If the maximum voltage of ADC input is 2V, output resistor value will be as below.
-6
-6
? 6.8[k ? ]
(2) L-Gain mode
Viout= 0.063 x 10 -6 x Ev x R1
3) C1
(1) To reject the flicker light..
In case IOUT output is R1 only and an ALS receives the artificial lights such as fluorescent lamps and incandescent
lamps synchronized with 50/60 Hz of AC power supplies, the output current has a ripple. If you want to reject this ripple,
please add C1 to R1 in parallel. Please set it to C1 x R1 = about 0.1 as a time constant.
(2) To control backlight smoothly by using illuminance value.
C1 is effective to control backlight smoothly for a rapid changing of the illuminance. In this case, please set it to C1 x R1
= about 1 ~ 10 as a time constant. It is not necessary if you average illuminance value with software to change backlight
smoothly.
Please note that the rise time becomes slow at power-on and recovery from shutdown mode to operation mode.
www.rohm.com
? 2012 ROHM Co., Ltd. All rights reserved.
5/9
2012.02 - Rev.D
相关PDF资料 |
PDF描述 |
|---|---|
| BH1715FVC-TR | IC AMBIENT LIGHT SENSOR 6-WSOF |
| BH1750FVI-TR | IC AMBIENT LIGHT SENSOR WSOF6 |
| BH1751FVI-TR | IC AMBIENT LIGHT SENSOR 6WSOF |
| BISDK02BI-03 | KIT BISM II BLUETOOTH/802.11B/G |
| BMS4007 | MOSFET N-CH 75V 60A TO-220ML |
相关代理商/技术参数 |
参数描述 |
|---|---|
| BH162240DGG | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:16-bit inverting buffer/driver with 30ohm series termination resistors |
| BH162240DL | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:16-bit inverting buffer/driver with 30ohm series termination resistors |
| BH162244DGG | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:16-bit buffer/line driver with 30ohm series termination resistors 3-State |
| BH162244DL | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:16-bit buffer/line driver with 30ohm series termination resistors 3-State |
| BH162245ADGG | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:16-Bit bus transceiver with 30ohm series termination resistors 3-State |
发布紧急采购，3分钟左右您将得到回复。