- 您现在的位置：买卖IC网 > PDF目录4529 > BR24T128FVT-WE2 (Rohm Semiconductor)IC EEPROM I2C 128K 400KHZ 8TSSOP PDF资料下载
参数资料
| 型号： | BR24T128FVT-WE2 |
| 厂商： | Rohm Semiconductor |
| 文件页数： | 7/22页 |
| 文件大小： | 0K |
| 描述： | IC EEPROM I2C 128K 400KHZ 8TSSOP |
| 标准包装： | 1 |
| 格式 - 存储器： | EEPROMs - 串行 |
| 存储器类型： | EEPROM |
| 存储容量： | 128K (16K x 8) |
| 速度： | 400kHz |
| 接口： | I²C，2 线串口 |
| 电源电压： | 1.7 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 8-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 8-TSSOP-B |
| 包装： | 标准包装 |
| 其它名称： | BR24T128FVT-WE2DKR |
BR24T □□□□ Series
Technical Note
I C BUS data communication
I C BUS data communication starts by start condition input, and ends by stop condition input. Data is always 8bit long,
and acknowledge is always required after each byte. I C BUS carries out data transmission with plural devices connected
● I 2 C BUS communication
2
2
2
by 2 communication lines of serial data (SDA) and serial clock (SCL).
Among devices, there are “master” that generates clock and control communication start and end, and “slave” that is
controlled by address peculiar to devices. EEPROM becomes “slave”. And the device that outputs data to bus during
data communication is called “transmitter”, and the device that receives data is called “receiver”.
SDA
SCL
1-7
8
9
1-7
8
9
1-7
8
9
S
P
START
ADDRESS
R/W
ACK
DATA
ACK
DATA
ACK
STOP
condition
condition
Fig.37 Data transfer timing
○ Start condition (Start bit recognition)
? Before executing each command, start condition (start bit) where SDA goes from 'HIGH' down to 'LOW' when SCL is
'HIGH' is necessary.
? This IC always detects whether SDA and SCL are in start condition (start bit) or not, therefore, unless this confdition is
satisfied, any command is executed.
○ Stop condition (stop bit recongnition)
? Each command can be ended by SDA rising from 'LOW' to 'HIGH' when stop condition (stop bit), namely, SCL is 'HIGH'
○ Acknowledge (ACK) signal
? This acknowledge (ACK) signal is a software rule to show whether data transfer has been made normally or not. In
master and slave, the device (μ-COM at slave address input of write command, read command, and this IC at data
output of read command) at the transmitter (sending) side releases the bus after output of 8bit data.
? The device (this IC at slave address input of write command, read command, and μ-COM at data output of read
command) at the receiver (receiving) side sets SDA 'LOW' during 9 clock cycles, and outputs acknowledge signal (ACK
signal) showing that it has received the 8bit data.
? This IC, after recognizing start condition and slave address (8bit), outputs acknowledge signal (ACK signal) 'LOW'.
? Each write action outputs acknowledge signal (ACK signal) 'LOW', at receiving 8bit data (word address and write data).
? Each read action outputs 8bit data (read data), and detects acknowledge signal (ACK signal) 'LOW'. When
acknowledge signal (ACK signal) is detected, and stop condition is not sent from the master (μ-COM) side, this IC
continues data output. When acknowledge signal (ACK signal) is not detected, this IC stops data transfer, and
recognizes stop cindition (stop bit), and ends read action. And this IC gets in status.
○ Device addressing
? Output slave address after start condition from master.
? The significant 4 bits of slave address are used for recognizing a device type.
The device code of this IC is fixed to '1010'.
? Next slave addresses (A2 A1 A0 --- device address) are for selecting devices, and plural ones can be used on a same
bus according to the number of device addresses.
? The most insignificant bit (R/W --- READ / WRITE ) of slave address is used for designating write or read action,
and is as shown below.
Setting R / W to 0 ------- write (setting 0 to word address setting of random read)
Setting R / W to 1 ------- read
Type
Slave address
Maximum number of
Connected buses
BR24T01-W,BR24T02-W
1
0
1 0
A2 A1
――
A0 R/ W
8
BR24T04-W
BR24T08-W
BR24T16-W
1
1
1
0
0
0
1
1
1
0
0
0
A2
A2
P2
A1
P1
P1
P0
P0
P0
――
R/ W
――
R/ W
――
R/ W
4
2
1
BR24T32-W,BR24T64-W,BR24T128-W,
BR24T256-W,BR24T512-W
BR24T1M-W
1
1
0
0
1 0
1 0
A2
A2
A1
A1
A0
P0
――
R/ W
――
R/ W
8
4
P0 ～ P2 are page select bits.
www.rohm.com
? 2011 ROHM Co., Ltd. All rights reserved.
7/21
2011.03 - Rev.A
相关PDF资料 |
PDF描述 |
|---|---|
| RSM36DRAH | CONN EDGECARD 72POS R/A .156 SLD |
| RMM36DRAH | CONN EDGECARD 72POS R/A .156 SLD |
| A3P060-FG144I | IC FPGA 1KB FLASH 60K 144-FBGA |
| A3P060-FGG144I | IC FPGA 1KB FLASH 60K 144-FBGA |
| EX64-TQG64I | IC FPGA ANTIFUSE 3K 64-TQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| BR24T128FVTWGE2 | 制造商:ROHM 制造商全称:Rohm 功能描述:High Reliability Serial EEPROMs |
| BR24T128FVT-WGE2 | 制造商:ROHM 制造商全称:Rohm 功能描述:High Reliability Serial EEPROMs |
| BR24T128FVTWGTR | 制造商:ROHM 制造商全称:Rohm 功能描述:High Reliability Serial EEPROMs |
| BR24T128FV-WE2 | 功能描述:电可擦除可编程只读存储器 Hi-Rel Serial 电可擦除可编程只读存储器 of I2C BUS RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 |
| BR24T128FVWGE2 | 制造商:ROHM 制造商全称:Rohm 功能描述:High Reliability Serial EEPROMs |
发布紧急采购，3分钟左右您将得到回复。