参数资料
| 型号： | BR93L56FJ-WE2 |
| 厂商： | Rohm Semiconductor |
| 文件页数： | 34/41页 |
| 文件大小： | 0K |
| 描述： | IC EEPROM 2KBIT 2MHZ 8SOP |
| 标准包装： | 2,500 |
| 格式 - 存储器： | EEPROMs - 串行 |
| 存储器类型： | EEPROM |
| 存储容量： | 2K (128 x 16) |
| 速度： | 2MHz |
| 接口： | Microwire 3 线串行 |
| 电源电压： | 1.8 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOP-J |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页当前第34页第35页第36页第37页第38页第39页第40页第41页
BR93L -W Series, 93A □□ -WM Series, BR93H □□ -WC Series
Technical Note
4-2) Timing of CS = “H” after write command. DO terminal in READY / BUSY function output.
When the next start bit input is recognized, “HIGH-Z” gets in.
→ Especially, at command input after write, when CS input is started with microcontroller DI/O output “L”,
READY output “H” is output from DO terminal, and through current route occurs.
Feedback input at timing of these 4-1) and 4-2) does not cause disorder in basic operations, if resistance R is inserted.
～ ～
EEPROM CS input
EEPROM SK input
EEPROM DI input
Write command
Write command
Write command
～ ～
～ ～
～ ～
～ ～
～ ～
BUSY
EEPROM DO output
Write command
～ ～
READY
～ ～
READY
High-Z
Collision of DI input and DO output
Microcontroller DI/O port
Write command
BUSY
～ ～
READY
～ ～
Microcontroller output
Microcontroller input
Microcontroller output
Fig.48 Collision timing at DI, DO direct connection
○ Selection of resistance value R
The resistance R becomes through current limit resistance at data collision. When through current flows, noises of
power source line and instantaneous stop of power source may occur. When allowable through current is defined as I,
the following relation should be satisfied. Determine allowable current amount in consideration of impedance and so
forth of power source line in set. And insert resistance R, and set the value R to satisfy EEPROM input level VIH/VIL,
even under influence of voltage decline owing to leak current and so forth. Insertion of R will not cause any influence
upon basic operations.
4-3) Address data A0 = “1” input, dummy bit “0” output timing
(When microcontroller DI/O output is “H”, EEPROM DO outputs “L”, and “H” is input to DI)
? Make the through current to EEPROM 10mA or below.
? See to it that the input level VIH of EEPROM should satisfy the following.
Conditions
Microcontroller
DI/O PORT
DI
EEPROM
VOHM ≦ VIHE
VOHM ≦ IOHM × R + VOLE
At this moment, if VOLE=0V,
“H” output
VOHM
VOHM ≦ IOHM × R
IOHM
R
DO
∴
R ≧
VOHM
IOHM
???⑦
VOLE
? VIHE
: EEPROM VIH specifications
“L” output
? VOLE
? VOHM
? IOHM
: EEPROM VOL specifications
: Microcontroller VOH specifications
: Microcontroller IOH specifications
Fig.49
Circuit at DI, DO direct connection (Microcontroller DI/O “H” output, EEPROM “L” output)
www.rohm.com
? 2011 ROHM Co., Ltd. All rights reserved.
34/40
2011.09 - Rev.G
相关PDF资料 |
PDF描述 |
|---|---|
| ASM40DTAH-S189 | CONN EDGECARD 80POS R/A .156 SLD |
| XC6VCX130T-1FFG784C | IC FPGA VIRTEX 6 128K 784FFGBGA |
| XC5VLX50T-2FFG665C | IC FPGA VIRTEX-5 50K 665FCBGA |
| XC5VLX50T-2FF665C | IC FPGA VIRTEX-5 50K 665FCBGA |
| XC5VFX30T-1FF665I | IC FPGA VIRTEX-5FXT 665FFBGA |
相关代理商/技术参数 |
参数描述 |
|---|---|
| BR93L56F-LE2 | 制造商:ROHM 制造商全称:Rohm 功能描述:High Reliability Serial EEPROMs High Reliability Series |
| BR93L56FV | 制造商:未知厂家 制造商全称:未知厂家 功能描述:EEPROM |
| BR93L56FVT-W | 制造商:ROHM 制造商全称:Rohm 功能描述:Microwire BUS 2Kbit(128 x 16bit) EEPROM |
| BR93L56FVT-WE2 | 功能描述:电可擦除可编程只读存储器 MICROWIRE BUS 2Kbit 1.8-5.5V Supply RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 |
| BR93L56FV-W | 制造商:ROHM Semiconductor 功能描述:EEPROM,2kb,128Wx16b,Microwire Bus,SSOP8 |
发布紧急采购，3分钟左右您将得到回复。