参数资料
型号: BR93L86RF-WE2
厂商: Rohm Semiconductor
文件页数: 36/41页
文件大小: 0K
描述: IC EEPROM 16KBIT 2MHZ 8SOP
标准包装: 1
格式 - 存储器: EEPROMs - 串行
存储器类型: EEPROM
存储容量: 16K (1K x 16)
速度: 2MHz
接口: Microwire 3 线串行
电源电压: 1.8 V ~ 5.5 V
工作温度: -40°C ~ 85°C
封装/外壳: 8-SOIC(0.173",4.40mm 宽)
供应商设备封装: 8-SOP
包装: 标准包装
产品目录页面: 1380 (CN2011-ZH PDF)
其它名称: BR93L86RF-WE2DKR
BR93L -W Series, 93A □□ -WM Series, BR93H □□ -WC Series
Technical Note
6) Notes on power ON/OFF
? At power ON/OFF, set CS “L”.
When CS is “H”, this IC gets in input accept status (active). At power ON, set CS “L” to prevent malfunction from noise.
(When CS is in “L” status, all inputs are cancelled.) At power decline low power status may prevail. Therefore, at power
OFF, set CS “L” to prevent malfunction from noise.
VCC
VCC
GND
VCC
CS
GND
Bad example
Good example
Fig.52 Timing at power ON/OFF
( Bad example ) CS pin is pulled up to Vcc.
In this case, CS becomes “H” (active status), EEPROM may
malfunction or have write error due to noises. This is true even
when CS input is High-Z.
( Good example ) It is “L” at power ON/OFF.
Set 10ms or higher to recharge at power OFF.
When power is turned on without observing this condition,
IC internal circuit may not be reset.
○ POR citcuit
This IC has a POR (Power On Reset) circuit as a mistake write countermeasure. After POR action, it gets in write
disable status. The POR circuit is valid only when power is ON, and does not work when power is OFF. However, if CS is
“H” at power ON/OFF, it may become write enable status owing to noises and the likes. For secure actions, observe the
follwing conditions.
1. Set CS=”L”
2. Turn on power so as to satisfy the recommended conditions of tR, tOFF, Vbot for POR circuit action.
t R
V CC
Recommended conditions of t R , t OFF , Vbot
t R
t O FF
V bot
10m s or below
10m s or higher 0.3V or below
0
○ LVCC circuit
t OFF
Vbot
Fig.53 Rise waveform diagram
100m s or below 10m s or higher 0.2V or below
LVCC (VCC-Lockout) circuit prevents data rewrite action at low power, and prevents wrong write.
At LVCC voltage (Typ.=1.9V) or below, it prevent data rewrite.
7) Noise countermeasures
○ VCC noise (bypass capacitor)
When noise or surge gets in the power source line, malfunction may occur, therefore, for removing these, it is
recommended to attach a by pass capacitor (0.1 μ F) between IC VCC and GND, At that moment, attach it as close to IC
as possible.And, it is also recommended to attach a bypass capacitor between board VCC and GND.
SK noise
When the rise time (tR) of SK is long, and a certain degree or more of noise exists, malfunction may occur owing to clock
bit displacement.
To avoid this, a Schmitt trigger circuit is built in SK input. The hysteresis width of this circuit is set about 0.3, if noises
exist at SK input, set the noise amplitude 0.3p-p or below. And it is recommended to set the rise time (tR) of SK 100ns or
below. In the case when the rise time is 100ns or higher, take sufficient noise countermeasures. Make the clock rise, fall
time as small as possible.
www.rohm.com
? 2011 ROHM Co., Ltd. All rights reserved.
36/40
2011.09 - Rev.G
相关PDF资料
PDF描述
ACB60DHAD CONN EDGECARD 120PS R/A .050 DIP
GCB120DHAN CONN EDGECARD 240PS R/A .050 SLD
RCB108DHAT CONN EDGECARD 216PS R/A .050 DIP
BR25L010F-WE2 IC EEPROM SER 1KB SPI BUS 8SOIC
GCB108DHAR CONN EDGECARD 216PS R/A .050 SLD
相关代理商/技术参数
参数描述
BR93L86-W 功能描述:IC EEPROM 16KBIT 2MHZ 8DIP RoHS:是 类别:集成电路 (IC) >> 存储器 系列:- 标准包装:1 系列:- 格式 - 存储器:闪存 存储器类型:闪存 - NAND 存储容量:4G(256M x 16) 速度:- 接口:并联 电源电压:2.7 V ~ 3.6 V 工作温度:0°C ~ 70°C 封装/外壳:48-TFSOP(0.724",18.40mm 宽) 供应商设备封装:48-TSOP I 包装:Digi-Reel® 其它名称:557-1461-6
BR93LC46 制造商:ROHM Semiconductor 功能描述: 制造商:Panasonic Industrial Company 功能描述:IC
BR93LC46A 制造商:未知厂家 制造商全称:未知厂家 功能描述:Microwire Serial EEPROM
BR93LC46AF 制造商:未知厂家 制造商全称:未知厂家 功能描述:Microwire Serial EEPROM
BR93LC46F 制造商:Panasonic Industrial Company 功能描述:IC