收藏本站
参数资料
型号： C8051F016-GQR
厂商： Silicon Laboratories Inc
文件页数： 96/171页
文件大小： 0K
描述： IC 8051 MCU 32K FLASH 48TQFP
产品培训模块： Serial Communication Overview
标准包装： 500
系列： C8051F01x
核心处理器： 8051
芯体尺寸： 8-位
速度： 25MHz
连通性： SMBus（2 线/I²C），SPI，UART/USART
外围设备： 欠压检测/复位，POR，PWM，温度传感器，WDT
输入/输出数： 16
程序存储器容量： 32KB（32K x 8）
程序存储器类型： 闪存
RAM 容量： 2.25K x 8
电压 - 电源 (Vcc/Vdd)： 2.7 V ~ 3.6 V
数据转换器： A/D 8x10b; D/A 2x12b
振荡器型： 内部
工作温度： -40°C ~ 85°C
封装/外壳： 48-TQFP
包装： 带卷 (TR)
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
5.2.
ADC Modes of Operation
The ADC uses VREF to determine its full-scale voltage, thus the reference must be properly configured before
performing a conversion (see Section 9). The ADC has a maximum conversion speed of 100ksps. The ADC
conversion clock is derived from the system clock. Conversion clock speed can be reduced by a factor of 2, 4, 8 or
16 via the ADCSC bits in the ADC0CF Register. This is useful to adjust conversion speed to accommodate
different system clock speeds.
A conversion can be initiated in one of four ways, depending on the programmed states of the ADC Start of
Conversion Mode bits (ADSTM1, ADSTM0) in ADC0CN. Conversions may be initiated by:
1.
Writing a 1 to the ADBUSY bit of ADC0CN;
2.
A Timer 3 overflow (i.e. timed continuous conversions);
3.
A rising edge detected on the external ADC convert start signal, CNVSTR;
4.
A Timer 2 overflow (i.e. timed continuous conversions).
Writing a 1 to ADBUSY provides software control of the ADC whereby conversions are performed “on-demand”.
During conversion, the ADBUSY bit is set to 1 and restored to 0 when conversion is complete. The falling edge of
ADBUSY triggers an interrupt (when enabled) and sets the ADCINT interrupt flag. Note: When conversions are
performed “on-demand”, the ADCINT flag, not ADBUSY, should be polled to determine when the
conversion has completed. Converted data is available in the ADC data word MSB and LSB registers, ADC0H,
ADC0L. Converted data can be either left or right justified in the ADC0H:ADC0L register pair (see example in
Figure 5.9) depending on the programmed state of the ADLJST bit in the ADC0CN register.
The ADCTM bit in register ADC0CN controls the ADC track-and-hold mode. In its default state, the ADC input is
continuously tracked, except when a conversion is in progress. Setting ADCTM to 1 allows one of four different
low power track-and-hold modes to be specified by states of the ADSTM1-0 bits (also in ADC0CN):
1.
Tracking begins with a write of 1 to ADBUSY and lasts for 3 SAR clocks;
2.
Tracking starts with an overflow of Timer 3 and lasts for 3 SAR clocks;
3.
Tracking is active only when the CNVSTR input is low;
4.
Tracking starts with an overflow of Timer 2 and lasts for 3 SAR clocks.
Modes 1, 2 and 4 (above) are useful when the start of conversion is triggered with a software command or when the
ADC is operated continuously. Mode 3 is used when the start of conversion is triggered by external hardware. In
this case, the track-and-hold is in its low power mode at times when the CNVSTR input is high. Tracking can also
be disabled (shutdown) when the entire chip is in low power standby or sleep modes.
Figure 5.2. 12-Bit ADC Track and Conversion Example Timing
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
CNVSTR
(ADSTM[1:0]=10)
ADCTM=1
Track
Convert
Low Power Mode
ADCTM=0
Track Or Convert
Convert
Track
Low Power or
Convert
Timer2, Timer3 Overflow;
Write 1 to ADBUSY
(ADSTM[1:0]=00, 01, 11)
ADCTM=1
Track
Convert
Low Power Mode
ADCTM=0
Track or Convert
Convert
Track
Low Power or
Convert
A. ADC Timing for External Trigger Source
B. ADC Timing for Internal Trigger Sources
SAR Clocks
1
234
56
78
9
10
11
12
13
14
15
16
17
18
19
1
234
56
78
9
10
11
12
13
14
15
16
SAR Clocks
Rev. 1.7
30
相关PDF资料
PDF描述
C8051F016-GQ IC 8051 MCU 32K FLASH 48TQFP
C8051F041-GQR IC 8051 MCU 64K FLASH 64TQFP
C8051F017-GQR IC 8051 MCU 32K FLASH 32LQFP
C8051F017-GQ IC 8051 MCU 32K FLASH 32LQFP
FIN1022M IC CROSSPOINT SWITCH 2X2 16SOIC
相关代理商/技术参数
参数描述
C8051F016R 功能描述:8位微控制器 -MCU C +-10Bit 48Pin RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
C8051F017 功能描述:8位微控制器 -MCU 32KB 10ADC RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
C8051F017-GQ 功能描述:8位微控制器 -MCU 32KB 10ADC 32P MCU RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
C8051F017-GQR 功能描述:8位微控制器 -MCU 32KB 10ADC 32Pin MCU Tape and Reel RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
C8051F017R 功能描述:8位微控制器 -MCU C +-10Bit 32Pin RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*