参数资料
型号: C8051F016
厂商: Silicon Laboratories Inc
文件页数: 165/171页
文件大小: 0K
描述: IC 8051 MCU 32K FLASH 48TQFP
标准包装: 250
系列: C8051F01x
核心处理器: 8051
芯体尺寸: 8-位
速度: 25MHz
连通性: SMBus(2 线/I²C),SPI,UART/USART
外围设备: 欠压检测/复位,POR,PWM,温度传感器,WDT
输入/输出数: 16
程序存储器容量: 32KB(32K x 8)
程序存储器类型: 闪存
RAM 容量: 2.25K x 8
电压 - 电源 (Vcc/Vdd): 2.7 V ~ 3.6 V
数据转换器: A/D 8x10b; D/A 2x12b
振荡器型: 内部
工作温度: -40°C ~ 85°C
封装/外壳: 48-TQFP
包装: 托盘
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
13. RESET SOURCES
The reset circuitry of the MCUs allows the controller to be easily placed in a predefined default condition. On entry
to this reset state, the CIP-51 halts program execution, forces the external port pins to a known state and initializes
the SFRs to their defined reset values. Interrupts and timers are disabled. On exit, the program counter (PC) is
reset, and program execution starts at location 0x0000.
All of the SFRs are reset to predefined values. The reset values of the SFR bits are defined in the SFR detailed
descriptions. The contents of internal data memory are not changed during a reset and any previously stored data is
preserved. However, since the stack pointer SFR is reset, the stack is effectively lost even though the data on the
stack are not altered.
The I/O port latches are reset to 0xFF (all logic ones), activating internal weak pull-ups which take the external I/O
pins to a high state. The weak pull-ups are enabled during and after the reset. If the source of reset is from the VDD
Monitor or writing a 1 to PORSF, the /RST pin is driven low until the end of the VDD reset timeout.
On exit from the reset state, the MCU uses the internal oscillator running at 2MHz as the system clock by default.
Refer to Section 14 for information on selecting and configuring the system clock source. The Watchdog Timer is
enabled using its longest timeout interval. (Section 13.8 details the use of the Watchdog Timer.)
There are seven sources for putting the MCU into the reset state: power-on/power-fail, external /RST pin, external
CNVSTR signal, software commanded, Comparator 0, Missing Clock Detector, and Watchdog Timer. Each reset
source is described below:
Figure 13.1. Reset Sources Diagram
WDT
CIP-51
Core
Missing
Clock
Detector
(one-
shot)
WD
T
Strobe
(Software Reset)
/RST
+
-
VDD
Supply
Reset
Timeout
(wired-OR)
System Reset
Supply
Monitor
PRE
Reset
Funnel
+
-
CP0+
Comparator 0
CP0-
(Port
I/O)
Crossbar
CNVSTR
CNVRSEF
C0RSEF
EN
WD
T
Enable
EN
MCD
Enable
SWRSF
System
Clock
93
Rev. 1.7
相关PDF资料
PDF描述
C8051F015 IC 8051 MCU 32K FLASH 64TQFP
C8051F236 IC 8051 MCU 8K FLASH 48TQFP
PIC14000-04I/SP IC MCU OTP 4KX14 A/D 28DIP
C8051F231 IC 8051 MCU 8K FLASH 32LQFP
C8051F230 IC 8051 MCU 8K FLASH 48TQFP
相关代理商/技术参数
参数描述
C8051F016-GQ 功能描述:8位微控制器 -MCU 32KB 10ADC 48P MCU RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
C8051F016-GQR 功能描述:8位微控制器 -MCU 32KB 10ADC 48Pin MCU Tape and Reel RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
C8051F016R 功能描述:8位微控制器 -MCU C +-10Bit 48Pin RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
C8051F017 功能描述:8位微控制器 -MCU 32KB 10ADC RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
C8051F017-GQ 功能描述:8位微控制器 -MCU 32KB 10ADC 32P MCU RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT