- 您现在的位置：买卖IC网 > PDF目录257720 > CAT1022WI45 (ON SEMICONDUCTOR) 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO8 PDF资料下载
参数资料
| 型号： | CAT1022WI45 |
| 厂商： | ON SEMICONDUCTOR |
| 元件分类： | 电源管理 |
| 英文描述： | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO8 |
| 封装： | 0.150 INCH, HALOGEN FREE AND ROHS COMPLIANT, MS-012, SOIC-8 |
| 文件页数： | 19/21页 |
| 文件大小： | 307K |
| 代理商： | CAT1022WI45 |
CAT1021, CAT1022, CAT1023
2007 Catalyst Semiconductor, Inc.
7
Doc. No. 3009 Rev. L
Characteristics subject to change without notice
DEVICE OPERATION
Reset Controller Description
The CAT1021/22/23 precision RESET controllers
ensure correct system operation during brownout and
power up/down conditions. They are configured with
open drain RESET outputs.
During power-up, the RESET outputs remain active
until VCC reaches the VTH threshold and will continue
driving the outputs for approximately 200ms (tPURST)
after reaching VTH. After the tPURST timeout interval, the
device will cease to drive the reset outputs. At this
point the reset outputs will be pulled up or down by
their respective pull up/down resistors.
During power-down, the RESET outputs will be active
when VCC falls below VTH. The RESET
output will be
valid so long as VCC is >1.0V (VRVALID). The device is
designed to ignore the fast negative going VCC
transient pulses (glitches).
Reset output timing is shown in Figure 1.
Manual Reset Operation
The RESET
pin can operate as reset output and
manual reset input. The input is edge triggered; that
is, the RESET
input will initiate a reset timeout after
detecting a high to low transition.
When RESET
I/O is driven to the active state, the 200
msec timer will begin to time the reset interval. If
external reset is shorter than 200ms, Reset outputs
will remain active at least 200ms.
The CAT1021/22/23 also have a separate manual
reset input. Driving the MR
input low by connecting a
pushbutton (normally open) from MR
pin to GND will
generate a reset condition. The input has an internal
pull up resistor.
Reset remains asserted while MR
is low and for the
Reset Timeout period after MR
input has gone high.
Glitches shorter than 100ns on MR
input will not ge-
nerate a reset pulse. No external debouncing circuits
are required. Manual reset operation using MR
input
is shown in Figure 2.
Hardware Data Protection
The CAT1021/22/23 supervisors have been designed
to solve many of the data corruption issues that have
long been associated with serial EEPROMs.
Data
corruption occurs when incorrect data is stored in a
memory location which is assumed to hold correct data.
Whenever the device is in a Reset condition, the
embedded EEPROM is disabled for all operations,
including write operations. If the Reset output(s) are
active, in progress communications to the EEPROM
are aborted and no new communications are allowed.
In this condition an internal write cycle to the memory
can not be started, but an in progress internal non-
volatile memory write cycle can not be aborted. An
internal write cycle initiated before the Reset condition
can be successfully finished if there is enough time
(5ms) before VCC reaches the minimum value of 2V.
In addition, the CAT1021 includes a Write Protection
Input which when tied to VCC will disable any write
operations to the device.
Watchdog Timer
The Watchdog Timer provides an independent
protection for microcontrollers. During a system
failure, CAT1021/22/23 devices will provide a reset
signal after a time-out interval of 1.6 seconds for a
lack of activity. The CAT1023 is designed with the
Watchdog timer feature on the WDI pin. The CAT1021
and CAT1022 monitor the SDA line. If WDI or SDA
does not toggle within a 1.6 second interval, the reset
condition will be generated on the reset outputs. The
watchdog timer is cleared by any transition on a
monitored line.
As long as reset signal is asserted, the watchdog
timer will not count and will stay cleared.
相关PDF资料 |
PDF描述 |
|---|---|
| CD-700KACGEB-35.328 | PHASE LOCKED LOOP, CQCC16 |
| CD-700KACGEB-51.840 | PHASE LOCKED LOOP, CQCC16 |
| CD-700KACGFB-24.576 | PHASE LOCKED LOOP, CQCC16 |
| CD-700KACGFB-30.000 | PHASE LOCKED LOOP, CQCC16 |
| CD-700KACGFB-34.368 | PHASE LOCKED LOOP, CQCC16 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| CAT1022WI-45-G | 功能描述:监控电路 CPU w/2K RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| CAT1022WI-45-GT2 | 制造商:CATALYST 制造商全称:Catalyst Semiconductor 功能描述:Supervisory Circuits with I2C Serial 2k-bit CMOS EEPROM, Manual Reset and Watchdog Timer |
| CAT1022WI-45-GT3 | 功能描述:监控电路 CPU SUP W/2K EEPROM RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| CAT1022WI-45T2 | 制造商:CATALYST 制造商全称:Catalyst Semiconductor 功能描述:Supervisory Circuits with I2C Serial 2k-bit CMOS EEPROM, Manual Reset and Watchdog Timer |
| CAT1022WI-45-T2 | 制造商:CATALYST 制造商全称:Catalyst Semiconductor 功能描述:Supervisory Circuits with I2C Serial 2k-bit CMOS EEPROM, Manual Reset and Watchdog Timer |
发布紧急采购，3分钟左右您将得到回复。