- 您现在的位置：买卖IC网 > PDF目录15171 > CAT1025WI-42-GT3 (ON Semiconductor)IC SUPERVISR CPU 2K EEPROM 8SOIC PDF资料下载
参数资料
| 型号： | CAT1025WI-42-GT3 |
| 厂商： | ON Semiconductor |
| 文件页数： | 9/20页 |
| 文件大小： | 0K |
| 描述： | IC SUPERVISR CPU 2K EEPROM 8SOIC |
| 标准包装： | 3,000 |
| 类型： | 简单复位/加电复位 |
| 监视电压数目： | 1 |
| 输出： | 开路漏极或开路集电极 |
| 复位： | 高有效/低有效 |
| 复位超时： | 最小为 130 ms |
| 电压 - 阀值： | 4.25V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOIC |
| 包装： | 带卷 (TR) |
CAT1024, CAT1025
EMBEDDED EEPROM OPERATION
I C BUS PROTOCOL
The CAT1024 and CAT1025 feature a 2-kbit embedded
serial EEPROM that supports the I 2 C Bus data
transmission protocol. This Inter-Integrated Circuit Bus
protocol defines any device that sends data to the bus to
be a transmitter and any device receiving data to be a
receiver. The transfer is controlled by the Master device
which generates the serial clock and all START and
STOP conditions for bus access. Both the Master device
and Slave device can operate as either transmitter
or receiver, but the Master device controls which mode
is activated.
2
The features of the I 2 C bus protocol are defined as
follows:
(1) Data transfer may be initiated only when the bus
is not busy.
(2) During a data transfer, the data line must remain
stable whenever the clock line is high. Any
changes in the data line while the clock line is
high will be interpreted as a START or STOP
condition.
START CONDITION
The START Condition precedes all commands to the
device, and is defined as a HIGH to LOW transition of
Figure 3. Bus Timing
SDA when SCL is HIGH. The CAT1024/25 monitors
the SDA and SCL lines and will not respond until this
condition is met.
STOP CONDITION
A LOW to HIGH transition of SDA when SCL is HIGH
determines the STOP condition. All operations must
end with a STOP condition.
DEVICE ADDRESSING
The Master begins a transmission by sending a
START condition. The Master sends the address of
the particular slave device it is requesting. The four
most significant bits of the 8-bit slave address are
programmable in metal and the default is 1010.
The last bit of the slave address specifies whether a
Read or Write operation is to be performed. When this
bit is set to 1, a Read operation is selected, and when
set to 0, a Write operation is selected.
ˉ ˉ
After the Master sends a START condition and the
slave address byte, the CAT1024/25 monitors the bus
and responds with an acknowledge (on the SDA line)
when its address matches the transmitted slave
address. The CAT1024/25 then perform a Read or
Write operation depending on the R/W bit.
SCL
tF
tLOW
tHIGH
tLOW
tR
tSU:STA
tHD:STA
tHD:DAT
tSU:DAT
tSU:STO
SDA IN
SDA OUT
Figure 4. Write Cycle Timing
SCL
tAA
tDH
tBUF
SDA
8TH BIT
BYTE n
ACK
tWR
STOP
CONDITION
START
CONDITION
ADDRESS
? 2009 SCILLC. All rights reserved.
Characteristics subject to change without notice
9
Doc. No. MD-3008 Rev. R
相关PDF资料 |
PDF描述 |
|---|---|
| ESRH680M08R | CAP ALUM 68UF 8V 20% SMD |
| ISL6552CRZ-T | IC REG CTRLR BUCK PWM 20-QFN |
| CAT1021WI-30-GT3 | IC SUPERVISR CPU 2K EEPROM 8SOIC |
| VI-J4K-EW-F1 | CONVERTER MOD DC/DC 40V 100W |
| RSM15DSEF | CONN EDGECARD 30POS .156 EYELET |
相关代理商/技术参数 |
参数描述 |
|---|---|
| CAT1025WI-42-T3 | 功能描述:监控电路 CPU w/2K RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| CAT1025WI45 | 功能描述:监控电路 CPU w/2K RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| CAT1025WI-45-G | 功能描述:监控电路 CPU w/2K RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| CAT1025WI-45-GT3 | 功能描述:监控电路 CPU w/2K RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| CAT1025WI-45-T3 | 功能描述:监控电路 CPU w/2K RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。