- 您现在的位置：买卖IC网 > PDF目录169495 > CAT24WC02RE-REV-F 256 X 8 I2C/2-WIRE SERIAL EEPROM, PDSO8 PDF资料下载
参数资料
| 型号： | CAT24WC02RE-REV-F |
| 元件分类： | PROM |
| 英文描述： | 256 X 8 I2C/2-WIRE SERIAL EEPROM, PDSO8 |
| 封装： | MO-187AA, MSOP-8 |
| 文件页数： | 11/14页 |
| 文件大小： | 505K |
| 代理商： | CAT24WC02RE-REV-F |
CAT24WC01/02/04/08/16
6
Doc. No. 1022, Rev. N
2005 by Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
address. The CAT24WC01/02/04/08/16 then performs
a Read or Write operation depending on the state of the
R/
W bit.
Acknowledge
After a successful data transfer, each receiving device is
required to generate an acknowledge. The Acknowledg-
ing device pulls down the SDA line during the ninth clock
cycle, signaling that it received the 8 bits of data.
The CAT24WC01/02/04/08/16 responds with an ac-
knowledge after receiving a START condition and its
slave address. If the device has been selected along
with a write operation, it responds with an acknowledge
after receiving each 8-bit byte.
When the CAT24WC01/02/04/08/16 is in a READ mode
it transmits 8 bits of data, releases the SDA line, and
monitors the line for an acknowledge. Once it receives
this acknowledge, the CAT24WC01/02/04/08/16 will
continue to transmit data. If no acknowledge is sent by
the Master, the device terminates data transmission and
waits for a STOP condition.
WRITE OPERATIONS
Byte Write
In the Byte Write mode, the Master device sends the
START condition and the slave address information
(with the R/
W bit set to zero) to the Slave device. After
the Slave generates an acknowledge, the Master sends
the byte address that is to be written into the address
pointer of the CAT24WC01/02/04/08/16. After receiving
another acknowledge from the Slave, the Master device
transmits the data byte to be written into the addressed
memory location. The CAT24WC01/02/04/08/16 ac-
knowledge once more and the Master generates the
STOP condition, at which time the device begins its
internal programming cycle to nonvolatile memory. While
this internal cycle is in progress, the device will not
respond to any request from the Master device.
Page Write
The CAT24WC01/02/04/08/16 writes up to 16 bytes of
data in a single write cycle, using the Page Write
operation. The Page Write operation is initiated in the
same manner as the Byte Write operation, however
instead of terminating after the initial word is transmitted,
Figure 5. Slave Address Bits
*
A0, A1 and A2 correspond to pin 1, pin 2 and pin 3 of the device.
**
a8, a9 and a10 correspond to the address of the memory array address word.
*** A0, A1 and A2 must compare to its corresponding hard wired input pins (pins 1, 2 and 3).
1
0
1
0
A2
A1
A0
R/W
1
0
1
0
A2
A1
a8
R/W
1
0
1
0
A2
a9
a8
R/W
1
0
1
0
a10
a9
a8
R/W
CAT24WC01/02
CAT24WC04
CAT24WC08
CAT24WC16
相关PDF资料 |
PDF描述 |
|---|---|
| CAT24WC02U-1.8REV-C | 256 X 8 I2C/2-WIRE SERIAL EEPROM, PDSO8 |
| CAT24WC02YA-1.8REV-E | 256 X 8 I2C/2-WIRE SERIAL EEPROM, PDSO8 |
| CAT24WC02WE-1.8REV-E | 256 X 8 I2C/2-WIRE SERIAL EEPROM, PDSO8 |
| CAT24WC02GYI-REV-C | 256 X 8 I2C/2-WIRE SERIAL EEPROM, PDSO8 |
| CAT24WC05LA-REV-A | 512 X 8 I2C/2-WIRE SERIAL EEPROM, PDIP8 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| CAT24WC02RI | 功能描述:电可擦除可编程只读存储器 (256x8) 2k 2.5-6.0 RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 |
| CAT24WC02RI-1.8 | 功能描述:电可擦除可编程只读存储器 (256x8) 2k 1.8-6.0 RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 |
| CAT24WC02U | 功能描述:电可擦除可编程只读存储器 (256x8) 2k 2.5-6.0 RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 |
| CAT24WC02U-1.8 | 功能描述:电可擦除可编程只读存储器 (256x8) 2k 1.8-6.0 RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 |
| CAT24WC02UA | 功能描述:电可擦除可编程只读存储器 (256x8) 2k 2.5-6.0 RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 |
发布紧急采购，3分钟左右您将得到回复。