参数资料
| 型号： | CAT25128YI-GT3 |
| 厂商： | ON Semiconductor |
| 文件页数： | 7/20页 |
| 文件大小： | 0K |
| 描述： | IC EEPROM 128KB SPI SER 8TSSOP |
| 标准包装： | 3,000 |
| 格式 - 存储器： | EEPROMs - 串行 |
| 存储器类型： | EEPROM |
| 存储容量： | 128K (16K x 8) |
| 速度： | 10MHz |
| 接口： | SPI 3 线串行 |
| 电源电压： | 1.8 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 8-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 8-TSSOP |
| 包装： | 带卷 (TR) |
CAT25128
Status Register
The Status Register, as shown in Table 11, contains a
number of status and control bits.
The RDY (Ready) bit indicates whether the device is busy
with a write operation. This bit is automatically set to 1 during
an internal write cycle, and reset to 0 when the device is ready
to accept commands. For the host, this bit is read only.
The WEL (Write Enable Latch) bit is set/reset by the
WREN/WRDI commands. When set to 1, the device is in a
Write Enable state and when set to 0, the device is in a Write
Disable state.
The BP0 and BP1 (Block Protect) bits determine which
blocks are currently write protected. They are set by the user
with the WRSR command and are non ? volatile. The user is
allowed to protect a quarter, one half or the entire memory,
by setting these bits according to Table 12. The protected
blocks then become read ? only.
The WPEN (Write Protect Enable) bit acts as an enable for
the WP pin. Hardware write protection is enabled when the
WP pin is low and the WPEN bit is 1. This condition
prevents writing to the status register and to the block
Table 11. STATUS REGISTER
protected sections of memory. While hardware write
protection is active, only the non ? block protected memory
can be written. Hardware write protection is disabled when
the WP pin is high or the WPEN bit is 0. The WPEN bit, WP
pin and WEL bit combine to either permit or inhibit Write
operations, as detailed in Table 13.
The IPL (Identification Page Latch) bit determines
whether the additional Identification Page (IPL = 1) or main
memory array (IPL = 0) can be accessed both for Read and
Write operations. The IPL bit is set by the user with the
WRSR command and is volatile. The IPL bit is
automatically reset after read/write operations.
The LIP bit is set by the user with the WRSR command
and is non ? volatile. When set to 1, the Identification Page is
permanently write protected (locked in Read ? only mode).
Note: The IPL and LIP bits cannot be set to 1 using the
same WRSR instruction. If the user attempts to set (“1”)
both the IPL and LIP bit in the same time, these bits cannot
be written and therefore they will remain unchanged.
7
WPEN
6
IPL*
5
0
4
LIP*
3
BP1
2
BP0
1
WEL
0
RDY
*The IPL and LIP bits are available for the New Product only. The Status Register bit 6 and bit 4 are set to “0” for the older product revisions.
Table 12. BLOCK PROTECTION BITS
Status Register Bits
BP1
0
0
1
1
BP0
0
1
0
1
Array Address Protected
None
3000 ? 3FFF
2000 ? 3FFF
0000 ? 3FFF
Protection
No Protection
Quarter Array Protection
Half Array Protection
Full Array Protection
Table 13. WRITE PROTECT CONDITIONS
WPEN
0
0
1
1
X
X
WP
X
X
Low
Low
High
High
WEL
0
1
0
1
0
1
Protected Blocks
Protected
Protected
Protected
Protected
Protected
Protected
Unprotected Blocks
Protected
Writable
Protected
Writable
Protected
Writable
Status Register
Protected
Writable
Protected
Protected
Protected
Writable
http://onsemi.com
7
相关PDF资料 |
PDF描述 |
|---|---|
| 346-020-522-204 | CARDEDGE 20POS DUAL .125 GREEN |
| 346-020-522-202 | CARDEDGE 20POS DUAL .125 GREEN |
| 346-020-522-201 | CARDEDGE 20POS DUAL .125 GREEN |
| 346-020-521-804 | CARDEDGE 20POS DUAL .125 GREEN |
| 346-020-521-802 | CARDEDGE 20POS DUAL .125 GREEN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| CAT25-130JA | 功能描述:电阻器网络与阵列 13ohm 5% Concave 8resistors RoHS:否 制造商:Vishay/Thin Film 产品类型:Networks 电路类型:Divider 电阻器数量: 电阻数值:10 kOhms 容差:0.1 % 温度系数: 管脚数量:3 工作温度范围:- 55 C to + 155 C 尺寸:1.02 mm W x 3.05 mm L x 1.4 mm H 引线间隔: 端接类型:SMD/SMT 封装:Reel |
| CAT25-130JALF | 功能描述:电阻器网络与阵列 13ohm 5% Concave 8resistors RoHS:否 制造商:Vishay/Thin Film 产品类型:Networks 电路类型:Divider 电阻器数量: 电阻数值:10 kOhms 容差:0.1 % 温度系数: 管脚数量:3 工作温度范围:- 55 C to + 155 C 尺寸:1.02 mm W x 3.05 mm L x 1.4 mm H 引线间隔: 端接类型:SMD/SMT 封装:Reel |
| CAT25-131JA | 功能描述:电阻器网络与阵列 130ohm 5% Concave 8resistors RoHS:否 制造商:Vishay/Thin Film 产品类型:Networks 电路类型:Divider 电阻器数量: 电阻数值:10 kOhms 容差:0.1 % 温度系数: 管脚数量:3 工作温度范围:- 55 C to + 155 C 尺寸:1.02 mm W x 3.05 mm L x 1.4 mm H 引线间隔: 端接类型:SMD/SMT 封装:Reel |
| CAT25-131JALF | 功能描述:电阻器网络与阵列 130ohm 5% Concave 8resistors RoHS:否 制造商:Vishay/Thin Film 产品类型:Networks 电路类型:Divider 电阻器数量: 电阻数值:10 kOhms 容差:0.1 % 温度系数: 管脚数量:3 工作温度范围:- 55 C to + 155 C 尺寸:1.02 mm W x 3.05 mm L x 1.4 mm H 引线间隔: 端接类型:SMD/SMT 封装:Reel |
| CAT25-141JALF | 功能描述:电阻器网络与阵列 140 ohm RoHS:否 制造商:Vishay/Thin Film 产品类型:Networks 电路类型:Divider 电阻器数量: 电阻数值:10 kOhms 容差:0.1 % 温度系数: 管脚数量:3 工作温度范围:- 55 C to + 155 C 尺寸:1.02 mm W x 3.05 mm L x 1.4 mm H 引线间隔: 端接类型:SMD/SMT 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。