- 您现在的位置：买卖IC网 > Datasheet目录318 > CAT3614HV2-T2 (ON Semiconductor)IC LED DRVR WHITE BCKLGT 12-TDFN Datasheet资料下载
参数资料
| 型号： | CAT3614HV2-T2 |
| 厂商： | ON Semiconductor |
| 文件页数： | 8/12页 |
| 文件大小： | 0K |
| 描述： | IC LED DRVR WHITE BCKLGT 12-TDFN |
| 标准包装： | 1 |
| 拓扑： | 切换式电容器（充电泵） |
| 输出数： | 4 |
| 内部驱动器： | 是 |
| 类型 - 主要： | 背光 |
| 类型 - 次要： | 白色 LED |
| 频率： | 800kHz ~ 1.3MHz |
| 电源电压： | 3 V ~ 5.5 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 12-WFDFN 裸露焊盘 |
| 供应商设备封装： | 12-TDFN（3x3） |
| 包装： | 标准包装 |
| 工作温度： | -40°C ~ 85°C |
| 产品目录页面： | 805 (CN2011-ZH PDF) |
| 其它名称： | CAT3614HV2-T2DKR |
CAT3614
Table 5. PIN DESCRIPTIONS
Pin #
1
2
3
4
5
6
7
8
9
10
11
12
TAB
Name
VIN
C1+
C1 ?
C2 ?
C2+
GND
LED1
LED2
LED3
LED4
EN/DIM
VOUT
TAB
Function
Supply voltage.
Bucket capacitor 1 terminal
Bucket capacitor 1 terminal
Bucket capacitor 2 terminal
Bucket capacitor 2 terminal
Ground reference
LED1 cathode terminal (if not used, connect to VOUT) (Note 3)
LED2 cathode terminal (if not used, connect to VOUT) (Note 3)
LED3 cathode terminal (if not used, connect to VOUT) (Note 3)
LED4 cathode terminal (if not used, connect to VOUT) (Note 3)
Device enable (active high) and dimming control input
Charge pump output connected to the LED anodes
Connect to GND on the PCB
3. LED1, LED2, LED3, LED4 pins should not be left floating. They should be connected to the LED cathode, or tied to VOUT pin if not used.
Pin Function
VIN is the supply pin for the charge pump. A small 1 m F
ceramic bypass capacitor is required between the VIN pin
and ground near the device. The operating input voltage
range is from 2.2 V to 5.5 V. Whenever the input supply falls
below the undervoltage threshold (2 V) all LEDs channels
will be automatically disabled.
EN/DIM is the enable and dimming control logic input for
all LED channels. Guaranteed levels of logic high and logic
low are set at 1.3 V and 0.4 V respectively. When EN/DIM
is initially taken high, the device becomes enabled and all
LED currents remain at 0 mA. The falling edge of the first
pulse applied to EN/DIM sets all LED currents to their full
scale of 31 mA.
On each consecutive falling edge of the pulse applied to
EN/DIM, the LED current is decreased by 1 mA step. On the
32nd pulse, the LED current is set to zero. The next pulse on
EN/DIM resets the current back to their full scale of 31 mA.
To place the device into zero current shutdown mode, the
EN/DIM pin must be held low for 1.5 ms or more.
VOUT is the charge pump output that is connected to the
LED anodes. A small 1 m F ceramic bypass capacitor is
required between the VOUT pin and ground near the device.
GND is the ground reference for the charge pump. The pin
must be connected to the ground plane on the PCB.
C1+, C1 ? are connected to each side of the 1 m F ceramic
bucket capacitor C1.
C2+, C2 ? are connected to each side of the 1 m F ceramic
bucket capacitor C2.
LED1 to LED4 provide the internal regulated current for
each of the LED cathodes. These pins enter a high
impedance zero current state whenever the device is placed
in shutdown mode. In applications using less than four
LEDs, all unused channels should be wired directly to
VOUT. This ensures the channel is automatically disabled
dissipating less than 200 m A.
TAB is the exposed pad underneath the package. For best
thermal performance, the tab should be soldered to the PCB
and connected to the ground plane.
http://onsemi.com
8
相关PDF资料 |
PDF描述 |
|---|---|
| CAT3616HV4-GT2 | IC LED DRVR WHITE BCKLGT 16-TQFN |
| CAT3636HV3-GT2 | IC LED DVR 6CH QUAD MODE 16TQFN |
| CAT3643HV2-T2 | IC LED DRVR WHITE BCKLGT 12-TDFN |
| CAT3644HV3-GT2 | IC LED DVR 4CH QUAD MODE 16TQFN |
| CAT3647HV3-GT2 | IC LED DRVR WHITE BCKLGT 16-TQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| CAT3616 | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:6-Channel Charge Pump LED Driver with EZDim |
| CAT3616_08 | 制造商:CATALYST 制造商全称:Catalyst Semiconductor 功能描述:6-Channel Charge Pump LED Driver with EZDimTM |
| CAT3616HV4 | 制造商:CATALYST 制造商全称:Catalyst Semiconductor 功能描述:6-Channel Charge Pump LED Driver with EZDimTM |
| CAT3616HV4-GT2 | 功能描述:LED照明驱动器 LED Driver,Charge pump,6 ch RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| CAT3616HV4-T2 | 功能描述:LED照明驱动器 LED Driver,Charge pump,6 ch RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
发布紧急采购，3分钟左右您将得到回复。