- 您现在的位置：买卖IC网 > Datasheet目录318 > CAT3661HV3-GT2 (ON Semiconductor)IC LED DRVR WHT BCKLGHT 16TQFN Datasheet资料下载
参数资料
| 型号： | CAT3661HV3-GT2 |
| 厂商： | ON Semiconductor |
| 文件页数： | 10/13页 |
| 文件大小： | 0K |
| 描述： | IC LED DRVR WHT BCKLGHT 16TQFN |
| 标准包装： | 1 |
| 系列： | QUAD-Mode® |
| 拓扑： | 切换式电容器（充电泵） |
| 输出数： | 1 |
| 内部驱动器： | 是 |
| 类型 - 主要： | 背光 |
| 类型 - 次要： | 白色 LED |
| 频率： | 100kHz，130kHz |
| 电源电压： | 2 V ~ 5.5 V |
| 输出电压： | 1.3 V ~ 4.2 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-WFQFN 裸露焊盘 |
| 供应商设备封装： | 16-TQFN（3x3） |
| 包装： | 标准包装 |
| 工作温度： | -40°C ~ 85°C |
| 其它名称： | CAT3661HV3-GT2OSDKR |
CAT3661
range. Extra external resistors can be added to the top or
bottom of the internal resistor divider network to alter the
divider ratio gain factor. The low battery indicator trip point
can be calculated by the following formula:
V LB + V ADJ G ADJ
V LB = Low Battery Voltage Trip Point
V ADJ = Low Battery Comparator Trip point (0.6 V)
G ADJ = Resistor Divider Gain (4 internally)
To obtain a low battery trip point of 2.4 V, the ADJH pin
is shorted to VIN, and the ADJL pin is tied to GND.
To increase the low battery trip point, insert a resistor
between ADJH and VIN. To consequently lower the low
For V LB > 2.4 V, use R L = 0 W and
R H (k W ) ? 200 (V LB /0.6 – 1) ? 600
For V LB < 2.4 V, use R H = 0 W and
R L (k W ) ? 600 (0.6/(V LB – 0.6)) – 200
Figure 26 shows the external resistor value for low battery
voltage trip points (V LB ) between 2 V and 3.2 V. For V LB
above 2.4 V, R L = 0 W . For V LB below 2.4 V, R H = 0 W .
240
200
160
battery trip point, insert a resistor between ADJL and GND.
The following formula shows how to calculate the modified
resistor divider gain:
120
80
RH
G ADJM +
R ADJ ) R H
(R ADJ G ADJ ) ) R L
40
RL
G ADJM = Modified resistor divider gain
R ADJ = Total resistance of divider (800 k W typ.)
R H = High external resistor (ADJH to VIN)
R L = Low external resistor (ADHL to GND)
0
2.0
2.2 2.4 2.6 2.8
TRIP POINT VOLTAGE (V)
Figure 26. V LB vs. R H & R L
3.0
3.2
The low battery trip point does not operate for adjustments
below 2.0 V VIN.
The inclusion of the ADJH pin allows monitoring of
supplies other than the supply to the CAT3661. Simply
connect ADJH pin directly to the supply to be monitored and
the low battery indicator will function as normal when the
device is enabled. When EN is low, no current will flow in
the resistor divider network allowing ‘zero’ current
shutdown mode.
Under Voltage Lockout
Figure 25. Application Circuit with R H & R L
The resistance required for a certain trip point voltage can
be calculated by rearranging the above equations with
respect to R H or R L .
If the voltage on VIN is less than V UVLO threshold, the
nFLTB output is driven low and the device enters a low
power state where the LED output is off.
When the device is in shutdown (EN low), the nFLTB pin
will float high to ‘zero’ current state.
http://onsemi.com
10
相关PDF资料 |
PDF描述 |
|---|---|
| CAT37TDI-T2 | IC LED DRVR WHITE BCKLGHT TSOT-5 |
| CAT4002ASD-GT3 | LED DR 2 CH EZ DIM I/F SC-88 |
| CAT4003BTD-GT3 | IC LED DVR 3CH TSOT23-6 |
| CAT4004AHU2-GT3B | IC LED DVR 4CH EZ DIM I/F 8DFN |
| CAT4004VP2-T3 | IC LED DRIVER LINEAR 8-TDFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| CAT37 | 制造商:TI 制造商全称:Texas Instruments 功能描述:CMOS White LED Driver Boost Converter |
| CAT37_05 | 制造商:CATALYST 制造商全称:Catalyst Semiconductor 功能描述:CMOS White LED Driver Boost Converter |
| CAT37_08 | 制造商:TI 制造商全称:Texas Instruments 功能描述:CMOS White LED Driver Boost Converter |
| CAT37EKK-TE7 | 制造商:CATALYST 制造商全称:Catalyst Semiconductor 功能描述:CMOS White LED Driver Boost Converter |
| CAT37RD4-TE13 | 制造商:CATALYST 制造商全称:Catalyst Semiconductor 功能描述:CMOS White LED Driver Boost Converter |
发布紧急采购，3分钟左右您将得到回复。