- 您现在的位置：买卖IC网 > Datasheet目录318 > CAT4106YP-T2 (ON Semiconductor)IC LED DVR 4CH BOOST 16TSSOP Datasheet资料下载
参数资料
| 型号： | CAT4106YP-T2 |
| 厂商： | ON Semiconductor |
| 文件页数： | 8/15页 |
| 文件大小： | 0K |
| 描述： | IC LED DVR 4CH BOOST 16TSSOP |
| 标准包装： | 1 |
| 恒定电流： | 是 |
| 拓扑： | PWM，升压（升压） |
| 输出数： | 4 |
| 内部驱动器： | 是 |
| 类型 - 主要： | 汽车，背光，通用型 |
| 频率： | 700kHz ~ 1.3MHz |
| 电源电压： | 3 V ~ 5.5 V |
| 输出电压： | 36V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-TSSOP（0.173"，4.40mm）裸露焊盘 |
| 供应商设备封装： | 16-TSSOP-EP |
| 包装： | 标准包装 |
| 工作温度： | -40°C ~ 85°C |
| 其它名称： | CAT4106YP-T2OSDKR |
CAT4106
Table 5. PIN DESCRIPTION
TQFN ? 16
Name
LED1
GND
FAULT
PGND
FB
SW
EN/PWM
N.C.
VIN
CTRL
VFMIN
VFMAX
RSET
LED4
LED3
LED2
TAB
Pin Descriptions
TSSOP ? 16
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
TAB
Function
LED1 cathode terminal
Signal Ground reference
Open/Short LED Fault detection output (active ? low)
Power Ground Reference (DC/DC Power Switch)
Feedback reference (300 mV) for setting LED channel operating voltage
Internal power FET switch drain connection
Device Enable (active high) and PWM control input
Not connected
Supply voltage for the device
LED channel operating voltage (lowest of all 4 channels)
Comparator input for setting the LED string short ? circuit voltage limit
Comparator input for setting the LED string open ? circuit voltage limit
RSET resistor pin for setting the LED channel operating current
LED4 cathode terminal
LED3 cathode terminal
LED2 cathode terminal
Thermal pad (connect to GND and PGND)
VIN is the supply pin for the device. The supply input
current needed for normal operation is approximately 2 mA
plus 3 times I RSET pin current. During intervals of PWM
dimming, or whenever the converter is not switching, the
supply current will decrease by around 1 mA. The voltage
applied at VIN should be kept between 3 V and 5.5 V. A
small ceramic bypass capacitor of 0.1 m F or greater is
recommended to be in close proximity to the VIN pin.
EN/PWM is the device Enable and PWM dimming control
input for all LED channels. Guaranteed levels of logic high
and logic low are set at 1.3 V and 0.4 V respectively. During
normal PWM dimming, the entire device remains fully
biased and only the LED channels are pulsed on/off. The
device will only enter zero current shutdown mode after the
EN/PWM is help low for at least 5 ms typically. This pin has
an internal pull ? down resistor of 200 k W .
RSET is the voltage regulated control pin for sensing the
desired programming current level to be applied on all LED
channels. During normal operation, the RSET pin is kept at
1.2 V and accurately monitors the current level in the
externally applied R1 resistor. The current transfer ratio
from RSET pin current to LED pin current is 100.
LED1 to LED4 provide the regulated current source for
driving each of the LED strings with a tightly matched
constant current. To ensure optimal performance, the bias
voltage on the LED channels should be set at a nominal
0.6 V or higher. Each channel is capable of driving a current
up to 175 mA. All channels immediately enter a high
impedance mode whenever the EN/PWM is taken LOW.
CTRL pin is a multiplexer output which selects the lowest
operating voltage appearing on any of the four LED output
drive channels. This control signal represents the cathode
terminal voltage of the LED string with greatest forward
voltage (V F ). An external resistor network from CTRL to FB
can be used to set the lowest operating voltage of each
channel. External current loading of the CTRL pin is
recommended to be less than 25 m A.
FB is the voltage feedback control pin for the internal high
power DC/DC converter. This pin has a high impedance
input and its voltage remains accurately regulated to 0.3 V
during normal steady state operation.
SW pin is the drain terminal of the high voltage CMOS
power switch which has a typical on ? resistance of 1 W and
is current limited to 1 A typically. An overvoltage protection
circuit places the device in a soft ? clamping low power mode
if the voltage transients exceed 40 V.
VFMIN pin uses a pair of external resistors (R6 & R7) to
program the worst case, minimum LED string forward
voltage (V FMIN ) expected in the specific application. If,
during power ? up, any LED string enters full regulation
before this programmed level is reached (VFMIN pin
voltage < 1.2 V), the string will be considered to contain
LEDs which are short ? circuit and a fault condition will be
http://onsemi.com
8
相关PDF资料 |
PDF描述 |
|---|---|
| CAT4109V-GT2 | IC LED DRIVER RGB 16-SOIC |
| CAT4134HV2-T2 | IC LED DRVR BKLGHT FLASH 12-TDFN |
| CAT4137TD-T3 | IC LED DRVR WHITE BCKLGHT TSOT-5 |
| CAT4139TD-GT3 | IC LED DRVR WHITE BCKLGT TSOT-5 |
| CAT4237TD-T3 | IC LED DRVR WHITE BCKLGHT TSOT-5 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| CAT4107HV4-GT2 | 制造商:ON Semiconductor 功能描述: |
| CAT4109 | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:3-Channel Constant-Current RGB LED Driver with Individual PWM Dimming |
| CAT4109VG | 制造商:Catalyst Semiconductor 功能描述: |
| CAT4109V-GT2 | 功能描述:LED照明驱动器 LED Driver 3ch RGB PWM RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| CAT4-11E | 制造商:ABB Control 功能描述:CONTACT BLKAUXFRNT1NO+1NC |
发布紧急采购，3分钟左右您将得到回复。