- 您现在的位置：买卖IC网 > Datasheet目录968 > CAT4201AEVB (ON Semiconductor)BOARD EVALUATION DPP CAT4201A Datasheet资料下载
参数资料
| 型号： | CAT4201AEVB |
| 厂商： | ON Semiconductor |
| 文件页数： | 7/14页 |
| 文件大小： | 0K |
| 描述： | BOARD EVALUATION DPP CAT4201A |
| 设计资源： | CAT4201AEVB Schematic CAT4201AEVB Gerber Files CAT4201AEVB Bill of Materials |
| 标准包装： | 1 |
| 系列： | * |
CAT4201
Table 6. PIN DESCRIPTION
Pin
1
2
3
4
5
Pin Function
Name
CTRL
GND
RSET
SW
VBAT
Function
Analog dimming control and shutdown pin.
Ground reference.
RSET pin. A resistor connected between the pin and ground sets the average LED current.
Interface to the inductor.
Supply voltage for the device.
VBAT is the supply input to the device. Typical current
conduction into this pin is less than 1 mA and voltage
transients of up to 40 V can be applied. To ensure accurate
LED current regulation, the VBAT voltage should be 3 V
higher than the total forward voltage of the LED string. A
bypass capacitor of 4.7 m F or larger is recommended
between VBAT and GND.
CTRL is the analog dimming and control input. An internal
pull ? down current of 20 m A allows the LEDs to shutdown
if CTRL is left floating. Voltages of up to 40 V can be safely
handled by the CTRL input pin.
When the CTRL voltage is less than 0.9 V (typ), the LEDs
will shutdown to zero current. When the CTRL voltage is
greater than about 2.6 V, full scale brightness is applied to the
LED output. At voltages of less than around 2.6 V, the LED
current is progressively dimmed until shutdown.
For lamp replacement applications, or applications where
operation in dropout mode is expected, it is recommended
that the CTRL pin voltage be derived from the LED cathode
terminal.
GND is the ground reference pin. This pin should be
connected directly to the ground plane on the PCB.
SW pin is the drain terminal of the internal low resistance
high ? voltage power MOSFET. The inductor and the
Schottky diode anode should be connected to the SW pin.
Voltages of up to 40 V can be safely handled on the SW pin.
Traces going to the SW pin should be as short as possible
with minimum loop area. The device can handle safely
“open ? LED” or “shorted ? LED” fault conditions.
RSET pin is regulated at 1.2 V. A resistor connected
between the RSET pin and ground sets the LED full ? scale
brightness current. The external resistance value and the
CTRL pin voltage determine the LED current during analog
dimming. The RSET pin must not be left floating. The
highest recommended resistor value between RSET and
ground is 90 k W .
http://onsemi.com
7
相关PDF资料 |
PDF描述 |
|---|---|
| CAT4238AEVB | BOARD EVALUATION DPP CAT4238A |
| CAT4240AEVB | BOARD EVALUATION DPP CAT4240A |
| CB1A-R-WM-12V | RELAY AUTOMOTIVE SPST 40A 12V |
| CB3127-000 | D-1744-03-LF |
| CB5065-000 | HEAT SHRINK TUBING |
相关代理商/技术参数 |
参数描述 |
|---|---|
| CAT4201AGEVB | 功能描述:LED 照明开发工具 EVAL BOARD FOR LED DRIVER RoHS:否 制造商:Fairchild Semiconductor 产品:Evaluation Kits 用于:FL7732 核心: 电源电压:120V 系列: 封装: |
| CAT4201TD | 制造商:ON Semiconductor 功能描述:IC LED DRIVER HI EFFICIENCY |
| CAT4201TD-GT3 | 功能描述:LED照明驱动器 350mA Hi-Efficiency Step-Down RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| CAT4201TD-GT3 | 制造商:ON Semiconductor 功能描述:IC LED DRIVER BUCK TSOT-23-5 制造商:ON Semiconductor 功能描述:IC, LED DRIVER, BUCK, TSOT-23-5 |
| CAT4237 | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:High Voltage CMOS Boost White LED Driver |
发布紧急采购，3分钟左右您将得到回复。