- 您现在的位置：买卖IC网 > Datasheet目录968 > CAT4201AEVB (ON Semiconductor)BOARD EVALUATION DPP CAT4201A Datasheet资料下载
参数资料
| 型号： | CAT4201AEVB |
| 厂商： | ON Semiconductor |
| 文件页数： | 9/14页 |
| 文件大小： | 0K |
| 描述： | BOARD EVALUATION DPP CAT4201A |
| 设计资源： | CAT4201AEVB Schematic CAT4201AEVB Gerber Files CAT4201AEVB Bill of Materials |
| 标准包装： | 1 |
| 系列： | * |
CAT4201
APPLICATION INFORMATION
Input Voltage Range
The minimum supply voltage required to maintain
adequate regulation is set by the cathode terminal voltage of
the LED string (i.e., the VBAT voltage minus the LED string
voltage). When the LED cathode terminal falls below 3 V,
a loss of regulation occurs.
For applications which may occasionally need to
experience supply “dropout” conditions, it is recommended
that the CTRL input be used to sense the LED cathode
voltage. The CTRL pin can either be tied directly to the
cathode terminal (for Lamp Replacement) or connected via
a pass ? transistor for PWM lighting applications.
Figure 23 shows the regulation performance obtained in
dropout, when the CTRL pin is configured to sense the LED
cathode voltage.
400
Capacitor Selection
A 10 m F ceramic capacitor C2 across the LED(s) keeps the
LED ripple current within ± 15% of nominal for most
applications. If needed, a larger capacitor can be used to
further reduce the LED current ripple. Any resistance in
series with the LED (0.5 W or more) contributes to reduce
the ripple current. The capacitor voltage rating should be
equivalent to the maximum expected supply voltage so as to
allow for “Open ? LED” fault conditions. The capacitor
value is independent of the switching frequency or the
overall efficiency.
A 4.7 m F ceramic input capacitor C1 is recommended to
minimize the input current ripple generated on the supply.
Using a larger capacitor value further reduces the ripple
noise appearing on the supply rail.
If a constant capacitance is needed across temperature and
voltage, X5R or X7R dielectric capacitors are recommended.
Schottky Diode
300
200
100
300 mA
150 mA
The peak repetitive current rating of the Schottky diode
must be greater than the peak current flowing through the
inductor. Also the continuous current rating of the Schottky
must be greater than the average LED current. The voltage
rating of the diode should be greater than the peak supply
voltage transient preventing any breakdown or leakage.
ON Semiconductor Schottky diode MBR0540 (40 V,
500 mA rated) is recommended. Schottky diodes rated at
400 mA (or higher) continuous current are fine for most
0
0 1 2 3 4 5
CTRL VOLTAGE [V]
Figure 23. “Dropout” Configured LED Current
6
applications.
NOTE: Schottky diodes with extremely low forward voltages
(V F ) are not recommended, as they may cause an
increase in the LED current.
(as shown in Typical Application on page 1)
Inductor Selection
A 22 m H minimum inductor value is required to provide
suitable switching frequency across a wide range of input
supply values. For LED current of 150 mA or less, a 33 m H
or 47 m H inductor is more suitable. Inductor values below
22 m H should not be used.
An inductor with at least 700 mA current rating must be
used. Minor improvements in efficiency can be achieved by
selecting inductors with lower series resistance.
Table 8. SUMIDA INDUCTORS
Dimming Methods
Two methods for PWM dimming control on the LEDs are
described below. The first method is to PWM on the control
pin, the other method is to turn on and off a second resistor
connected to the RSET pin and connected in parallel with R1.
PWM on CTRL Pin
A PWM signal from a microprocessor can be used for
dimming the LEDs when tied to the CTRL pin. The duty
cycle which is the ratio between the On time and the total
cycle time sets the dimming factor. The recommended PWM
frequency on the CTRL pin is between 100 Hz and 2 kHz.
Part Number
CDRH6D26 ? 220
CDRH6D28 ? 330
CDRH6D28 ? 470
CDRH6D28 ? 560
L ( m H)
22
33
47
56
I Rated (A)
1.0
0.92
0.8
0.73
LED Current (A)
0.35
0.35
0.35
0.35
Figure 24. PWM at 1 kHz on CTRL Pin
http://onsemi.com
9
相关PDF资料 |
PDF描述 |
|---|---|
| CAT4238AEVB | BOARD EVALUATION DPP CAT4238A |
| CAT4240AEVB | BOARD EVALUATION DPP CAT4240A |
| CB1A-R-WM-12V | RELAY AUTOMOTIVE SPST 40A 12V |
| CB3127-000 | D-1744-03-LF |
| CB5065-000 | HEAT SHRINK TUBING |
相关代理商/技术参数 |
参数描述 |
|---|---|
| CAT4201AGEVB | 功能描述:LED 照明开发工具 EVAL BOARD FOR LED DRIVER RoHS:否 制造商:Fairchild Semiconductor 产品:Evaluation Kits 用于:FL7732 核心: 电源电压:120V 系列: 封装: |
| CAT4201TD | 制造商:ON Semiconductor 功能描述:IC LED DRIVER HI EFFICIENCY |
| CAT4201TD-GT3 | 功能描述:LED照明驱动器 350mA Hi-Efficiency Step-Down RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| CAT4201TD-GT3 | 制造商:ON Semiconductor 功能描述:IC LED DRIVER BUCK TSOT-23-5 制造商:ON Semiconductor 功能描述:IC, LED DRIVER, BUCK, TSOT-23-5 |
| CAT4237 | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:High Voltage CMOS Boost White LED Driver |
发布紧急采购，3分钟左右您将得到回复。