- 您现在的位置：买卖IC网 > PDF目录298944 > CAT521W SPECIALTY ANALOG CIRCUIT, PDSO14 PDF资料下载
参数资料
| 型号： | CAT521W |
| 元件分类： | 模拟信号调理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PDSO14 |
| 封装： | LEAD-FREE, SOIC-14 |
| 文件页数： | 6/10页 |
| 文件大小： | 71K |
| 代理商： | CAT521W |
CAT521
5
Doc. No. 2003, Rev. F
PIN DESCRIPTION
Pin
Name
Function
1VDD
Power supply positive
2
CLK
Clock input pin
3
RDY/
BSY
Ready/Busy output
4
CS
Chip select
5
DI
Serial data input pin
6
DO
Serial data output pin
7
PROG
EEPROM Programming Enable
Input
8
GND
Power supply ground
9VREFL
Minimum DAC output voltage
10
NC
No Connect
11
NC
No Connect
12
VOUT
DPP output
13
NC
No Connect
14
VREFH
Maximum DPP 1 output voltage
DEVICE OPERATION
The CAT521 is a single 8-bit configured digitally
programmable potentiometer (DPP) whose output
can be programmed to any one of 256 individual voltage
steps. Once programmed, the output setting is retained
in non-volatile memory and will not be lost when power
is removed from the chip. Upon power up the DPP
returns to the setting stored in non-volatile memory. The
DPP can be written to and read from without effecting the
output voltage during the read or write cycle. The output
can also be adjusted without altering the stored output
setting, which is useful for testing new output settings
before storing them in memory.
DIGITAL INTERFACE
The CAT521 employs a 3 wire, Microwire-like serial
control interface consisting of Clock (CLK), Chip Select
(CS) and Data In (DI) inputs. For all operations, address
and data are shifted in LSB first. In addition, all digital
data must be preceded by a logic “1” as a start bit. The
DPP address and data are clocked into the DI pin on the
clock’s rising edge. When sending multiple blocks of
information a minimum of two clock cycles is required
between the last block sent and the next start bit.
Multiple devices may share a common input data line by
selectively activating the CS control of the desired IC.
Data Outputs (DO) can also share a common line
because the DO pin is Tri-Stated and returns to a high
impedance when not in use.
CHIP SELECT
Chip Select (CS) enables and disables the CAT521’s
read and write operations. When CS is high data may be
read to or from the chip, and the Data Output (DO) pin is
active. Data loaded into the DPP control register will
remain in effect until CS goes low. Bringing CS to a logic
low returns all DPP outputs to the settings stored in non-
volatile memory and switches DO to its high impedance
Tri-State mode.
Because CS functions like a reset the CS pin has been
desensitized with a 30 ns to 90 ns filter circuit to prevent
noise spikes from causing unwanted resets and the loss
of volatile data.
CLOCK
The CAT521 clock controls both data flow in and out of
the device and non-volatile memory cell programming.
Serial data is shifted into the DI pin and out of the DO pin
on the clock’s rising edge. While it is not necessary for
the clock to be running between data transfers, the clock
must be operating in order to write to non-volatile memory,
even though the data being saved may already be
resident in the DPP wiper control register.
No clock is necessary upon system power-up. The
CAT521 internal power-on reset circuitry loads data
from non-volatile memory to the DPP without using the
external clock.
DPP addressing is as follows:
DPP OUTPUT
A0
A1
VOUT
10
相关PDF资料 |
PDF描述 |
|---|---|
| CAT706TZI-GT3 | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO8 |
| CAT813ZI-GT3 | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO8 |
| CAT809LSDI-T | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO3 |
| CAT809MEUR-T | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO3 |
| CAT809ZTBI-T | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO3 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| CAT521WI | 功能描述:数字电位计 IC Ind Temp 28K 3-Wire RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
| CAT521WI-T3 | 功能描述:数字电位计 IC DPP NV 256 taps 3 wire w/Buf RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
| CAT5221WI00 | 制造商:ON Semiconductor 功能描述:DPP, NV, QUAD 64 TAPS, I2C - Rail/Tube |
| CAT5221WI-00 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Catalyst Semiconductor 功能描述: |
| CAT5221WI-00-T1 | 功能描述:数字电位计 IC DPP NV QUAD 64 TAPS I2C RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。