参数资料
| 型号： | CBC-EVAL-08 |
| 厂商： | Cymbet Corporation |
| 文件页数： | 3/11页 |
| 文件大小： | 0K |
| 描述： | ENERCHIP EH SEH EVAL KIT |
| 产品目录绘图： | CBC-EVAL-08 Module |
| 特色产品： | EnerChip? EH Solar Energy Harvesting Evaluation Kit |
| 标准包装： | 1 |
| 系列： | EnerChip™ EH |
| 主要目的： | 电源管理，可再生能源 |
| 嵌入式： | 否 |
| 已用 IC / 零件： | CBC5300 |
| 主要属性： | 薄膜充电式固态电池 |
| 次要属性： | 太阳能收集器 |
| 已供物品： | 板 |
| 相关产品： | 859-1009-6-ND - IC BATT SOLID ST ENERCHIP 16QFN 859-1009-1-ND - IC BATT SOLID ST ENERCHIP 16QFN 859-1009-2-ND - IC BATT SOLID ST ENERCHIP 16QFN 859-1005-5-ND - IC BATT SOLID ST ENERCHIP 16QFN |
| 其它名称： | 859-1002 |
EnerChip Solar Energy Harvesting Demo Kit
Connecting CBC-EVAL-08 to the System
The CBC-EVAL-08 board has two control lines that can be connected to a microcontroller (MCU) for the purpose
of conserving available energy, using incoming power efficiently, and extending EnerChip life. The table below
describes the functionality of the J1 and J5 connector pins.
J1 and J5 Pin Descriptions
Pin
BATOFF
CHARGE
V BAT
(not accessible from the J1 connector)
V OUT2
GND
Designation
Input control line to the CBC-EVAL-08 for disconnecting the
EnerChips from the CBC-EVAL-08 charging circuit. See the section
Circuit Recommendations to Save Power for additional information.
Active low output from the CBC-EVAL-08 indicating that the Ener-
Chips have been charged or are being charged. This is an open
drain output with an internal 10M? pull-up resistor to V OUT2 . See
the section Circuit Recommendations to Save Power for additional
information.
Connected indirectly to the EnerChips’ positive terminals through
an isolation FET. Voltage is one diode drop above the potential at
V OUT2.
System power
System ground
? V OUT2 is the DC output voltage from the CBC-EVAL-08 and is approximately 3.5V depending on load
current. It provides power to the system according to the Operating Characteristics table shown below.
? GND is the ground connection of the CBC-EVAL-08. It is to be connected to the system ground line.
? V BAT is normally used for factory test purposes. It is indirectly connected to the on-board EnerChips
through an isolation pass transistor. The voltage on V BAT is connected to V OUT2 by a diode and thus the
voltage at V OUT2 is one diode drop lower than the voltage on V BAT . It is recommended that V BAT remain
disconnected from external circuits. In no event should V BAT be used for any purpose other than to provide
power to a load.
? BATOFF is typically controlled by a microcontroller I/O line. When driven high, the on-board EnerChips will
be disconnected from the charging source of the CBC-EVAL-08. This feature allows all available power to be
delivered to the load rather than to charging the EnerChips, a useful mode when limited transducer power
is available or when higher operating current is required from the system. When BATOFF is driven low, the
interaction between the charging source and the CBC-EVAL-08 behaves normally. In other words, when
BATOFF is low the EnerChips will always be charging when sufficient input power is available.
? CHARGE is an output signal from the CBC-EVAL-08 that will be forced low under one of two conditions:
? When transducer output power is very low, a low level on CHARGE indicates that the
EnerChips have been charged.
? CHARGE will also be driven low when transducer output power is more than sufficient to operate
the boost converter and charge the EnerChips at peak rate, regardless of the state of charge of the
EnerChips. Programming an MCU timer to allow enough charging time to elapse after the assertion
of CHARGE will ensure that the EnerChips are fully charged before using them to deliver power to the
system. The advantage is that the system is then aware of the minimum reservoir of energy available in
the event transducer power goes to zero.
DS-72-08 Rev18
?2009 Cymbet Corporation ? Tel: +1-763-633-1780 ? www.cymbet.com
Page 3 of 11
相关PDF资料 |
PDF描述 |
|---|---|
| CBC-EVAL-09 | ENERCHIP EP ENERGY HARVEST EVAL |
| CBC-EVAL-11 | INDUCTIVE CHARGING EVAL KIT |
| CBJ157 | TRS JACK STR PCB SLD POT 3-LUG |
| CBJ70 | TRB JACK STR PCB 3-LUG |
| CBJR12 | MINI-WECO PATCH JACK 75OHM R/A |
相关代理商/技术参数 |
参数描述 |
|---|---|
| CBC-EVAL-08_10 | 制造商:CYMBET 制造商全称:CYMBET 功能描述:EnerChipa?￠ EH Solar Energy Harvester Evaluation Kit |
| CBC-EVAL-09 | 功能描述:电源管理IC开发工具 EnerChip EP Universal EH Kit RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| CBC-EVAL-09 - DSC | 功能描述:CBC915-ACA, CBC51100 EnerChip? Series Power Management, Energy Harvesting Evaluation Board 制造商:cymbet corporation 系列:EnerChip?? 零件状态:有效 主要用途:电源管理，能量收集 嵌入式:否 使用的 IC/零件:CBC915-ACA，CBC51100 主要属性:EM/RF，太阳能，热能，振动能量处理器 辅助属性:- 所含物品:板 标准包装:1 |
| CBC-EVAL-09_13 | 制造商:CYMBET 制造商全称:CYMBET 功能描述:EnerChip EP Universal Energy Harvester Eval Kit |
| CBC-EVAL-10 | 功能描述:电源管理IC开发工具 EnerChip CCEH EH Kit RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
发布紧急采购，3分钟左右您将得到回复。