参数资料
| 型号： | CBC-EVAL-08 |
| 厂商： | Cymbet Corporation |
| 文件页数： | 9/11页 |
| 文件大小： | 0K |
| 描述： | ENERCHIP EH SEH EVAL KIT |
| 产品目录绘图： | CBC-EVAL-08 Module |
| 特色产品： | EnerChip? EH Solar Energy Harvesting Evaluation Kit |
| 标准包装： | 1 |
| 系列： | EnerChip™ EH |
| 主要目的： | 电源管理，可再生能源 |
| 嵌入式： | 否 |
| 已用 IC / 零件： | CBC5300 |
| 主要属性： | 薄膜充电式固态电池 |
| 次要属性： | 太阳能收集器 |
| 已供物品： | 板 |
| 相关产品： | 859-1009-6-ND - IC BATT SOLID ST ENERCHIP 16QFN 859-1009-1-ND - IC BATT SOLID ST ENERCHIP 16QFN 859-1009-2-ND - IC BATT SOLID ST ENERCHIP 16QFN 859-1005-5-ND - IC BATT SOLID ST ENERCHIP 16QFN |
| 其它名称： | 859-1002 |
EnerChip Solar Energy Harvesting Demo Kit
Troubleshooting Test Procedure
1) Using a voltmeter, put the ground lead on J5 pin 4 and probe J7 (left pin). Voltage should be 1.0V. This test
verifies operation of the photovoltaic cell.
2) Probe right side of the tantalum capacitor (brown bar side) on the CBC5300 module. Voltage should be
between 4.5V and 9V depending on ambient light and EnerChip device state-of-charge. This test verifies
operation of the boost converter.
3) Probe the positive (bottom side) terminal of capacitor C2 on the CBC-EVAL-08. Voltage should be 4.06V,
or steadily increasing if there is no output voltage. When the capacitor voltage reaches 3.8V, the output
will turn on from zero volts to the voltage across capacitor C2. Note C2 will not be charging if the EnerChips
are depleted. When the CBC-EVAL-08 is first powered up, the CBC5300 will first charge the EnerChips, then
charge the output capacitor C2, then switch on the output when C2 is charged.
4) Probe J5 Pin 3 (VBAT). This pin should be at 4.06V.
5) Probe J5 Pin 5 (VOUT). This pin should be at 3.5V.
6) Probe J5 Pin 1 (CHARGE/). This pin should be at zero volts if the EnerChips are charged and enough
ambient energy is available to operate the CBC5300 module. Depending on the input impedance of the
voltmeter, a high level on this pin would read between 1.0V and 3.5V.
If none of the above works, check pin 1 on one of the EnerChips on the CBC5300 module (with it plugged
into the solar board), as indicated in the figure below. It should read approximately 3.9V. If the voltage is less
than 3.0V, the EnerChips have been damaged.
In applications where a radio is being used - as in wireless sensor networks - there can sometimes be
external electrical interference with the radio signal that causes the radio receiver to stay on longer than
normal. If this happens, the CBC-EVAL-08 output capacitor C2 will become discharged and the low voltage
cutoff circuit will engage, isolating the EnerChips from the load. If this happens it can take from several
minutes to an hour or more for the EnerChips and output capacitor to be recharged.
EnerChip Pin 1
DS-72-08 Rev18
?2009 Cymbet Corporation ? Tel: +1-763-633-1780 ? www.cymbet.com
Page 9 of 11
相关PDF资料 |
PDF描述 |
|---|---|
| CBC-EVAL-09 | ENERCHIP EP ENERGY HARVEST EVAL |
| CBC-EVAL-11 | INDUCTIVE CHARGING EVAL KIT |
| CBJ157 | TRS JACK STR PCB SLD POT 3-LUG |
| CBJ70 | TRB JACK STR PCB 3-LUG |
| CBJR12 | MINI-WECO PATCH JACK 75OHM R/A |
相关代理商/技术参数 |
参数描述 |
|---|---|
| CBC-EVAL-08_10 | 制造商:CYMBET 制造商全称:CYMBET 功能描述:EnerChipa?￠ EH Solar Energy Harvester Evaluation Kit |
| CBC-EVAL-09 | 功能描述:电源管理IC开发工具 EnerChip EP Universal EH Kit RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| CBC-EVAL-09 - DSC | 功能描述:CBC915-ACA, CBC51100 EnerChip? Series Power Management, Energy Harvesting Evaluation Board 制造商:cymbet corporation 系列:EnerChip?? 零件状态:有效 主要用途:电源管理，能量收集 嵌入式:否 使用的 IC/零件:CBC915-ACA，CBC51100 主要属性:EM/RF，太阳能，热能，振动能量处理器 辅助属性:- 所含物品:板 标准包装:1 |
| CBC-EVAL-09_13 | 制造商:CYMBET 制造商全称:CYMBET 功能描述:EnerChip EP Universal Energy Harvester Eval Kit |
| CBC-EVAL-10 | 功能描述:电源管理IC开发工具 EnerChip CCEH EH Kit RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
发布紧急采购，3分钟左右您将得到回复。