- 您现在的位置：买卖IC网 > PDF目录67391 > CBTL06121AHF (NXP Semiconductors N.V.) Gen1 hex display multiplexer PDF资料下载
参数资料
| 型号： | CBTL06121AHF |
| 厂商： | NXP Semiconductors N.V. |
| 元件分类： | 编、解码器及复用、解复用 |
| 英文描述： | Gen1 hex display multiplexer |
| 封装： | CBTL06121AHF<SOT1033-1 (HWQFN56R)|<<http://www.nxp.com/packages/SOT1033-1.html<1<Always Pb-free,;CBTL06121BHF<SOT1033-1 (HWQFN56R)|<<http://www.nxp.com/packages/SOT1033-1 |
| 文件页数： | 4/20页 |
| 文件大小： | 162K |
| 代理商： | CBTL06121AHF |
CBTL06121
All information provided in this document is subject to legal disclaimers.
NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 2 — 26 October 2010
12 of 20
NXP Semiconductors
CBTL06121
Gen1 hex display multiplexer
10.4 HPD input, HPD output
[1]
Low-speed input changes state on cable plug/unplug.
[2]
Time from HPD_IN changing state to HPD changing state. Includes HPD rise/fall time.
10.5 MUX select and latch input
11. Test information
11.1 Switch test fixture requirements
The test fixture for switch S-parameter measurement shall be designed and built to
specific requirements, as described below, to ensure good measurement quality and
consistency.
The test fixture shall be a FR4-based PCB of the microstrip structure; the dielectric
thickness or stack-up shall be about 4 mils.
The total thickness of the test fixture PCB shall be 1.57 mm (0.62 in).
The measurement signals shall be launched into the switch from the top of the test
fixture, capturing the through-hole stub effect.
Traces between the DUT and measurement ports (SMA or microprobe) should be
uncoupled from each other, as much as possible. Therefore, the traces should be
routed in such a way that traces will diverge from each other exiting from the switch
pin field.
The trace lengths between the DUT and measurement port shall be minimized. The
maximum trace length shall not exceed 1000 mils. The trace lengths between the
DUT and measurement port shall be equal.
All of the traces on the test board and add-in card must be held to a characteristic
impedance of 50
Ω with a tolerance of ±7%.
SMA connector is recommended for ease of use. The SMA launch structure shall be
designed to minimize the connection discontinuity from SMA to the trace. The
impedance range of the SMA seen from a TDR with a 60 ps rise time should be
within 50
Ω± 7 Ω.
Table 11.
HPD input and output characteristics
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
VI
input voltage
0.3
-
3.6
V
tPD
propagation delay
from HPD_SINK to HPD_SOURCE
[2] -180
-
ps
Table 12.
SEL, LE_N input characteristics
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
VIH
HIGH-level input voltage
2.0
-
3.6
V
VIL
LOW-level input voltage
0
-
0.8
V
ILI
input leakage current
measured with input at
VIH(max) and VIL(min)
--
10
μA
相关PDF资料 |
PDF描述 |
|---|---|
| CBTL06121BHF | Gen1 hex display multiplexer |
| CBTL06122AHF | High-performance DisplayPort-PCIe Gen2 hex display multiplexer |
| CBTL06122BHF | High-performance DisplayPort-PCIe Gen2 hex display multiplexer |
| CBTL06DP211EE | DisplayPort Gen1 2 : 1 multiplexer |
| CBTL06DP212EE | High-performance DisplayPort Gen2 2 : 1 multiplexer |
相关代理商/技术参数 |
参数描述 |
|---|---|
| CBTL06121AHF,518 | 功能描述:编码器、解码器、复用器和解复用器 GEN1 HEX DISPLAY RoHS:否 制造商:Micrel 产品:Multiplexers 逻辑系列:CMOS 位数: 线路数量（输入/输出）:2 / 12 传播延迟时间:350 ps, 400 ps 电源电压-最大:2.625 V, 3.6 V 电源电压-最小:2.375 V, 3 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:QFN-44 封装:Tray |
| CBTL06121AHF-T | 功能描述:编码器、解码器、复用器和解复用器 GEN1 HEX DISPLAY MULTIPLEXER RoHS:否 制造商:Micrel 产品:Multiplexers 逻辑系列:CMOS 位数: 线路数量（输入/输出）:2 / 12 传播延迟时间:350 ps, 400 ps 电源电压-最大:2.625 V, 3.6 V 电源电压-最小:2.375 V, 3 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:QFN-44 封装:Tray |
| CBTL06121BHF | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Gen1 hex display multiplexer |
| CBTL06121BHF,518 | 功能描述:编码器、解码器、复用器和解复用器 GEN1 HEX DISPLAY RoHS:否 制造商:Micrel 产品:Multiplexers 逻辑系列:CMOS 位数: 线路数量（输入/输出）:2 / 12 传播延迟时间:350 ps, 400 ps 电源电压-最大:2.625 V, 3.6 V 电源电压-最小:2.375 V, 3 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:QFN-44 封装:Tray |
| CBTL06121BHF-T | 功能描述:编码器、解码器、复用器和解复用器 GEN1 HEX DISPLAY MULTIPLEXER RoHS:否 制造商:Micrel 产品:Multiplexers 逻辑系列:CMOS 位数: 线路数量（输入/输出）:2 / 12 传播延迟时间:350 ps, 400 ps 电源电压-最大:2.625 V, 3.6 V 电源电压-最小:2.375 V, 3 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:QFN-44 封装:Tray |
发布紧急采购，3分钟左右您将得到回复。