参数资料
| 型号： | CDB35L00 |
| 厂商： | Cirrus Logic Inc |
| 文件页数： | 5/12页 |
| 文件大小： | 0K |
| 描述： | DEVELOPMENT BOARD FOR CS35L0X |
| 产品培训模块： | CS35L0x Audio Amplifiers Overview |
| 视频文件： | CS42L73 and CS35L00/01/03 |
| 标准包装： | 1 |
| 放大器类型： | D 类 |
| 输出类型： | 4-通道（四路） |
| 在某负载时最大输出功率 x 通道数量： | 2.7W x 4 @ 4 欧姆 |
| 电源电压： | 2.5 V ~ 5.5 V |
| 板类型： | 完全填充 |
| 已用 IC / 零件： | CS35L0X |
| 已供物品： | 板 |
| 产品目录页面： | 758 (CN2011-ZH PDF) |
| 其它名称： | 598-1803 |
CDB35L00-X4
1.4.1
Shutdown Control Resistors
The CDB35L00-X4 contains 0 ohm resistors (R1-R4) which
allow the individual CS35L00 shutdown pins to be discon-
nected from the S1 switch or connected to an external con-
trol device. These resistors are located on the back side of
the CDB35L00-X4 board near S1, as shown highlighted in
R1-R4 are connected to SD on U1-U4, respectively. It is rec-
ommended that the individual shutdown line pull-up resistors
for U1-U4 (R10, R20, R30, R40) be left populated to help
prevent the individual SD control lines from floating.
Figure 2. Shutdown Control Resistors
SD1-2
SD3-4
LOW
HIGH
U1 & U2 OFF
U1 & U2 ON
U3 & U4 OFF
U3 & U4 ON
Table 3. S1 Switch Default Shutdown Configurations
1.5
Gain Control
The amplifier gain of the CS35L00 can be configured to operate with either a +6 dB gain or a +12 dB gain
as shown in Table 1 on page 3 . The amplifier gain is selectable through the GAIN setting on the S1 switch.
Note:
The CS35L00 devices should be placed into shutdown via either the S1 switch or by removing pow-
er before changing the GAIN setting.
1.5.1
Optional Gain Adjustment Resistors
The CDB35L00-X4 contains optional gain adjustment resistor placeholders for each CS35L00 device
(R11, R12, R21, R22, R31, R32, R41, R42). By default these are not populated and the CS35L00 oper-
ates at its gain control setting as set by the S1 switch. See Table 1 . The gain adjustment resistors are only
necessary when a gain of +6 dB or a gain of +12 dB is not desired. By adding series resistance to the
input, the signal amplitude to the CS35L00 will be reduced, and will reduce the overall system gain. The
typical input impedance values of the CS35L00 as well as how to calculate the resistor values for a de-
sired gain can be found in the device datasheet.
In order to use the optional gain adjustment resistors for U1, the traces between the R11 pads and the
traces between the R12 pads must be cut in order to break the bypass circuit before populating R11 and
R12 with the desired resistance values. The location of these required cuts are shown in Figure 3 on page
6 . After the trace between the pads has been broken, the gain adjustment resistors can be added to the
board.
The gain adjustment resistors for U2, U3, and U4 can be added in the same manner as is described for
U1 (above).
DS913DB2
5
相关PDF资料 |
PDF描述 |
|---|---|
| CDB4207 | BOARD EVALUATION FOR CS4207 |
| CDB4245 | BOARD EVAL FOR CS4245 CODEC |
| CDB42L55 | BOARD EVAL FOR CS42L55 CODEC |
| CDB44L11 | EVALUATION BOARD FOR CS44L11 |
| CDB48500-USB | KIT USB EVALUATION FOR CDB48500 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| CDB35L00-X4 | 制造商:CIRRUS 制造商全称:Cirrus Logic 功能描述:2.7 W x 4 CS35L00 Amplifier Demonstration Board |
| CDB36-A | 制造商:Panduit Corp 功能描述: |
| CDB37MM25 | 制造商:DigitHead Inc 功能描述:COMPUTERS |
| CDB-37PF | 制造商:HRS 制造商全称:HRS 功能描述:CD CRIMP TYPE CONNECTOR |
| CDB-37SF | 制造商:HRS 制造商全称:HRS 功能描述:CD CRIMP TYPE CONNECTOR |
发布紧急采购，3分钟左右您将得到回复。