- 您现在的位置：买卖IC网 > PDF目录17058 > CDB4392 (Cirrus Logic Inc)EVALUATION BOARD FOR CS4392 PDF资料下载
参数资料
| 型号： | CDB4392 |
| 厂商： | Cirrus Logic Inc |
| 文件页数： | 8/40页 |
| 文件大小： | 0K |
| 描述： | EVALUATION BOARD FOR CS4392 |
| 标准包装： | 1 |
| DAC 的数量： | 2 |
| 位数： | 24 |
| 采样率（每秒）： | 192k |
| 数据接口： | 串行 |
| DAC 型： | 电压 |
| 工作温度： | -10°C ~ 70°C |
| 已供物品： | 板 |
| 已用 IC / 零件： | CS4392 |
| 相关产品： | 598-1065-5-ND - IC DAC 24BIT 192KHZ W/VC 20TSSOP |
第1页第2页第3页第4页第5页第6页第7页当前第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页
CS4392
16
DS459PP3
4.0.3
SPI Mode
In SPI mode, data is clocked into the serial control data line, CDIN, by the serial control port clock,
CCLK (see Figure 9 for the clock to data relationship). There is no AD0 pin. Pin CS is the chip
select signal and is used to control SPI writes to the control port. When the device detects a high to
low transition on the AD0/CS pin after power-up, SPI mode will be selected. All signals are inputs
and data is clocked in on the rising edge of CCLK.
4.0.3a
SPI Write
To write to the device, follow the procedure below while adhering to the control port
Switching Specifications in section 7.
1) Bring CS low.
2) The address byte on the CDIN pin must then be 00100000.
3) Write to the memory address pointer, MAP. This byte points to the register to be written.
4) Write the desired data to the register pointed to by the MAP.
5) If the INCR bit (see section 4.0.1) is set to 1, repeat the previous step until all the desired
registers are written, then bring CS high.
6) If the INCR bit is set to 0 and further SPI writes to other registers are desired, it is nec-
essary to bring CS high, and follow the procedure detailed from step 1. If no further writes
to other registers are desired, bring CS high.
4.1
Memory Address Pointer (MAP)
MAP
MSB
LS B
DATA
byte 1
byte n
R/W
MA P = Me mo ry A d dre s s P o in te r
ADDRESS
CH IP
CD IN
CC L K
CS
00 10 00 0
Figure 9. Control Port Timing, SPI mode
4.1.1 INCR (AUTO MAP INCREMENT ENABLE)
Default = ‘0’
0 - Disabled,
the MAP will stay constant for successive writes
1 - Enabled,
the MAP will auto increment after each byte is written, allowing block reads or
writes of successive registers
4.1.2 MAP3-0 (MEMORY ADDRESS POINTER)
Default = ‘0000’
76543210
INCR
Reserved
MAP3
MAP2
MAP1
MAP0
00000000
相关PDF资料 |
PDF描述 |
|---|---|
| 0210490185 | CABLE JUMPER 1.25MM .254M 12POS |
| RPP20-1215D/N | CONV DC/DC 20W 9-18VIN +/-15VOUT |
| SDR0604-220YL | INDUCTOR POWER 22UH 1.10A SMD |
| EBA22DTKD-S288 | CONN EDGECARD 44POS .125 EXTEND |
| 380LX562M035H022 | CAP ALUM 5600UF 35V 20% SNAP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| CDB4396 | 制造商:CIRRUS 制造商全称:Cirrus Logic 功能描述:24-Bit, 192 kHz D/A Converter for Digital Audio |
| CDB4397 | 制造商:CIRRUS 制造商全称:Cirrus Logic 功能描述:24-Bit, Multi-Standard D/A Converter for Digital Audio |
| CDB4398 | 功能描述:音频 IC 开发工具 Eval Bd RoHS:否 制造商:Texas Instruments 产品:Evaluation Kits 类型:Audio Amplifiers 工具用于评估:TAS5614L 工作电源电压:12 V to 38 V |
| CDB43L21 | 功能描述:音频 IC 开发工具 Eval Bd 98dB 96kHz Low-Pwr DAC RoHS:否 制造商:Texas Instruments 产品:Evaluation Kits 类型:Audio Amplifiers 工具用于评估:TAS5614L 工作电源电压:12 V to 38 V |
| CDB43L22 | 功能描述:音频 IC 开发工具 Eval Bd LP DAC w/ClassD Spkr Driver RoHS:否 制造商:Texas Instruments 产品:Evaluation Kits 类型:Audio Amplifiers 工具用于评估:TAS5614L 工作电源电压:12 V to 38 V |
发布紧急采购，3分钟左右您将得到回复。