- 您现在的位置：买卖IC网 > PDF目录125560 > CM2320-7EPD0 2-OUTPUT 50 W DC-DC REG PWR SUPPLY MODULE PDF资料下载
参数资料
| 型号： | CM2320-7EPD0 |
| 元件分类： | 电源模块 |
| 英文描述： | 2-OUTPUT 50 W DC-DC REG PWR SUPPLY MODULE |
| 封装： | METAL, CASE M02, MODULE |
| 文件页数： | 24/25页 |
| 文件大小： | 569K |
| 代理商： | CM2320-7EPD0 |
Cassette Style
DC-DC Converters
M Series
Edition 01/01.2001
8/25
Thermal Protection
A temperature sensor generates an internal inhibit signal
which disables the outputs if the case temperature exceeds
TC max. The outputs are automatically re-enabled if the tem-
perature drops below this limit.
Output Protection
Each output is protected against overvoltages which could
occur due to a failure of the internal control circuit. Voltage
suppressor diodes (which under worst case condition may
become a short circuit) provide the required protection. The
suppressor diodes are not designed to withstand externally
applied overvoltages. Overload at any of the outputs will
cause a shut-down of all outputs. A red LED indicates the
overload condition of the respective output.
Parallel and Series Connection
Main outputs of equal nominal voltage can be connected in
parallel. It is important to assure that the main output of a
multiple output module is forced to supply a minimum cur-
rent of 0.1 A to enable correct operation of its own auxiliary
outputs.
In parallel operation, one or more of the main outputs may
operate continuously in current limitation which will cause
an increase in case temperature. Consequently, a reduction
of the max. ambient temperature by 10 K is recommended.
Main or auxiliary outputs can be connected in series with
any other output of the same or another module. In series
connection, the maximum output current is limited by the
lowest current limit. Output ripple and regulation values are
added. Connection wiring should be kept as short as possi-
ble.
If output terminals are connected together in order to estab-
lish multi-voltage configurations, e.g. +5.1 V,
±12 V etc. the
common ground connecting point should be as close as
possible to the connector of the converter to avoid exces-
sive output ripple voltages.
Auxiliary outputs should never be connected in parallel!
Thermal Considerations
If a converter is located in free, quasi-stationary air (con-
vection cooling) at the indicated maximum ambient tem-
perature
TA max (see table: Temperature specifications) and
is operated at its nominal input voltage and output power,
the temperature measured at the:
Measuring point of case
temperature TC (see: Mechanical Data) will approach the
indicated value
TC max after the warm-up phase. However,
the relationship between
TA and TC depends heavily on the
conditions of operation and integration into a system. The
thermal conditions are influenced by input voltage, output
current, airflow and temperature of surrounding compo-
nents and surfaces.
TA max is therefore, contrary to TC max,
an indicative value only.
Caution: The installer must ensure that under all operat-
ing conditions
TC remains within the limits stated in the
table:
Temperature specifications.
Notes: Sufficient forced cooling or an additional heat sink
allows
TA to be higher than 71
°C (e.g. 85°C) if T
C max is not
exceeded.
For -7 or -9 units at an ambient temperature
TA of 85
°C with
only convection cooling, the maximum permissible current
for each output is approx. 50% of its nominal value as per
figure.
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
50
60
70
80
90
100
Io/Io nom
TA [°C]
0.9
1.0
Forced cooling
05031
TA min
TC max
Convection cooling
Fig. 6
Output current derating versus temperature for -7 and -9
units.
1.0
0
0.5
U
o1
0.5
U
o1 nom
I
o
I
o nom
1.0
1.2
I
o nom
I
o1
I
o2,Io3
I
oL1
I
oL2,IoL3
.95
05022
Io/Io nom
1
uod
t d
DUo I
t
Uo
0
t
≥10 s
05010
Fig. 4
Typical output voltage Uo1 versus output currents Io.
Fig. 5
Dynamic load regulation uo d versus load change.
相关PDF资料 |
PDF描述 |
|---|---|
| CM2320-7EPD5HF | 2-OUTPUT 50 W DC-DC REG PWR SUPPLY MODULE |
| CM2320-7PA | 2-OUTPUT 50 W DC-DC REG PWR SUPPLY MODULE |
| CM2320-7PV3 | 2-OUTPUT 50 W DC-DC REG PWR SUPPLY MODULE |
| CM2320-9PA | 2-OUTPUT 50 W DC-DC REG PWR SUPPLY MODULE |
| CM2320-9PD7AHF | 2-OUTPUT 50 W DC-DC REG PWR SUPPLY MODULE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| CM2320-7ET2 | 功能描述:DC/DC CONVERTER DUAL 12V 2A 制造商:bel power solutions 系列:Melcher M 包装:散装 零件状态:有效 类型:隔离 电压 - 输入:28 ~ 140 V 输出:12V 输出数:2 不同电流时的输出（最大值） - 1:12 VDC @ 2A 不同电流时的输出（最大值） - 2:12 VDC @ 2A 不同电流时的输出（最大值） - 3:- 不同电流时的输出（最大值） - 4:- 功率（W）:48W 应用:ITE（商业），铁路 安装类型:底座安装 工作温度:-25°C ~ 71°C 效率:79% 封装/外壳:- 大小/尺寸:6.63" 长 x 4.38" 宽 x 1.52" 高（168.5mm x 111.2mm x 38.7mm） 功率（W） - 最大值:48W 认可:cCSAus，CE 标准包装:5 |
| CM2320-9 | 制造商:Power-One 功能描述:DC/DC PS DUAL-OUT 12V 2A 50W 11PIN - Bulk |
| CM2321-000 | 制造商:TE Connectivity 功能描述:55/LF0114-28-94CS3254 |
| CM2322-000 | 制造商:TE Connectivity 功能描述:55/LF0114-28-95CS3254 |
| CM2323 | 制造商:CML 制造商全称:Chicago Miniature Lamp,inc 功能描述:T-1 3/4 Bi-Pin Base (.125) |
发布紧急采购，3分钟左右您将得到回复。