- 您现在的位置：买卖IC网 > PDF目录16880 > CMAXQUSB+ (Maxim Integrated Products)MODULE COMMAND SMBUS/I2C PDF资料下载
参数资料
| 型号： | CMAXQUSB+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 7/16页 |
| 文件大小： | 0K |
| 描述： | MODULE COMMAND SMBUS/I2C |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 1 |
| 系列： | * |
CMAXQUSB User’s Guide
Connector P7: SMBus/I 2 C Test Points
For convenience, the SMBus/I 2 C interface signals are
connected to labeled pins on header P7. See Table 5.
Table 5. Connector P7 Description
Detailed Description of Firmware
The CMAXQUSB firmware was developed using
the MAX-IDE assembly language development
environment. Full source code is available at
www.maxim-ic.com/tools/evkit under the project
P7 PIN
1
2
3
4
LABEL
VDD
SDA
GND
SCL
FUNCTION
VDD Power Supply
SMBus/I 2 C SDA (Data)
Ground Return
SMBus/I 2 C SCL (Clock)
name CMAXQUSB Firmware .
If designing a custom EV kit board requiring an inter-
rupt service routine in custom firmware, GPIO signals
K5–K8 are the suggested locations for the interrupt sig-
nal. The standard CMAXQUSB firmware does not ser-
vice interrupts on any GPIO pins.
Connector P8: SPI Test Points
For convenience, the SPI interface signals are connect-
ed to labeled pins on header P8. See Table 6.
Table 6. Connector P8 Description
Troubleshooting
Problem: Software reports it cannot find the board.
? Verify that the CMAXQUSB power LED is lit.
? Verify that the USB cable is connected.
? Verify that Windows plug-and-play detected the
P8 PIN
1
2
3
4
5
6
LABEL
VDD
MISO
MOSI
SCLK
CS
GND
FUNCTION
VDD Power Supply
Master-In, Slave-Out Data
Master-Out, Slave-In Data
SPI Clock
Chip Select. Configurable active
high or active low.
Ground Return
board. Bring up Control Panel -> System -> Device
Manager, and look at what device nodes are indicat-
ed for the USB. If there is an “unknown device” node
attached to the USB, delete it—this forces plug-and-
play to try again.
Problem: Unable to find SMBus/I 2 C device.
? Verify that the SCL and SDA signals are pulled up to
VDD. CMAXQUSB DIP switch SW1 enables the on-
board resistors. There must be pullup resistors
somewhere on the bus.
? If using wires to connect the CMAXQUSB to your
target board, make certain that you have not
swapped the SCL and SDA signals. Verify that the
ground return is connected.
7
相关PDF资料 |
PDF描述 |
|---|---|
| EBC24DCMI-S288 | CONN EDGECARD 48POS .100 EXTEND |
| 222D174-3-60-0 | BOOT MOLDED |
| EBC20DCAI-S189 | CONN EDGECARD 40POS R/A .100 SLD |
| VI-JNN-EY | CONVERTER MOD DC/DC 18.5V 50W |
| 222D242-4-61/42-0 | BOOT MOLDED |
相关代理商/技术参数 |
参数描述 |
|---|---|
| CMAXQUSB+ | 功能描述:界面开发工具 Evaluation Brd RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V |
| CMB | 功能描述:12V (6.0 ~ 15.0 V) 180W AC DC Configurable Power Supply Module 制造商:excelsys technologies ltd 系列:CoolX?600 NFF 零件状态:新产品 类型:单路直流输出模块 功率（W）:180W 电流:15A 电压 - 输出:12.0 标称值，6.0 ~ 15.0 范围 标准包装:1 |
| CMB 8141-0 | 制造商:TURCK Inc 功能描述:Connector, Female, 4 Pin, Eurofast, PG9, 6-8mm cable, 18AWG, 250V, 4A |
| CMB 8151-0 | 制造商:TURCK Inc 功能描述:Connector, M12 Female Straight, FA, 5 Wire, Screw, 6-8mm, U6112 制造商:TURCK Inc 功能描述:CONNECTOR EUROFAST 制造商:TURCK Inc 功能描述:CONNECTOR, EUROFAST 制造商:TURCK Inc 功能描述:CONNECTOR, EUROFAST; For Use With:Sensors; Accessory Type:Sensor Connector; Current Rating:4A; Gender:Receptacle; No. of Contacts:5; Voltage Rating:60V ;RoHS Compliant: Yes |
| CMB 8181-0 | 制造商:TURCK Inc 功能描述:Connector, M12 FA Female Straight, 8 Wire, Screw, 6-8mm Cable, U0885-23 制造商:TURCK Inc 功能描述:CONNECTOR EUROFAST 制造商:TURCK Inc 功能描述:CONNECTOR, EUROFAST 制造商:TURCK Inc 功能描述:CONNECTOR, EUROFAST; For Use With:Sensors; Accessory Type:Sensor Connector; Current Rating:2A; Gender:Receptacle; No. of Contacts:8; Voltage Rating:60V ;RoHS Compliant: Yes |
发布紧急采购，3分钟左右您将得到回复。