- 您现在的位置：买卖IC网 > PDF目录298953 > CMX644AD2 (CML MICROSYSTEMS PLC) 1.2 kbps DATA, MODEM, PDSO24 PDF资料下载
参数资料
| 型号： | CMX644AD2 |
| 厂商： | CML MICROSYSTEMS PLC |
| 元件分类： | 调制器/解调器 |
| 英文描述： | 1.2 kbps DATA, MODEM, PDSO24 |
| 封装： | SOIC-24 |
| 文件页数： | 26/34页 |
| 文件大小： | 1174K |
| 代理商： | CMX644AD2 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页当前第26页第27页第28页第29页第30页第31页第32页第33页第34页
RPM-Based Fan Controller with HW Thermal Shutdown
Datasheet
Revision 0.90 (08-19-08)
32
SMSC EMC2103
DATASHEET
4. Set the Fan Minimum Drive Register to the minimum drive value that will maintain fan operation.
5. Set the Update Time, and Edges options in the Fan Configuration Register.
6. Set the valid TACH count setting at the highest count that indicates that the fan is spinning.
7. Set the TACH Target Register to the desired tachometer count.
8. Enable the RPM based Fan Speed Control Algorithm by setting the EN_ALGO bit.
5.6
Tachometer Measurement
The tachometer measurement circuitry is used in conjunction with the RPM based Fan Speed Control
Algorithm to update the fan driver output. Additionally, it can be used in Direct Setting mode as a
diagnostic for host based fan control.
This method monitors the TACH signal in real time. It constantly updates the tachometer measurement
by reporting the number of clocks between a user programmed number of edges on the TACH signal.
Using the Tach Period Measurement method provides fast response times for the RPM based Fan
Speed Control Algorithm and the data is presented as a count value that represents the fan RPM
period. When this method is used, all fan target values must be input as a count value for proper
operation.
APPLICATION NOTE: The Tach Period Measurement method works independently of the drive settings. If the
device is put into Direct Setting and the fan drive is set at a level that is lower than the fan
can operate (including zero drive), then the tachometer measurement may signal a Stalled
Fan condition and assert an interrupt.
5.6.1
Stalled Fan
A Stalled fan is detected differently based on which tach method is enabled. If the Tach Period
Measurement measurement method is implemented, and if the tach counter exceeds the user-
programmable Valid TACH Count setting then it will flag the fan as stalled and trigger an interrupt.
If the RPM based Fan Speed Control Algorithm is enabled, the algorithm will automatically attempt to
restart the fan until it detects a valid tachometer level or is disabled.
The FAN_STALL Status bit indicates that a stalled fan was detected. This bit is checked conditionally
depending on the mode of operation.
When the Direct Setting Mode or Direct Setting with LUT Mode are enabled or the Spin Up Routine
is initiated, the FAN_STALL interrupt will be masked for the duration of the programmed Spin Up
Time. This is to allow the fan opportunity to reach a valid speed without generating unnecessary
interrupts.
When the Direct Setting Mode or Direct Setting w/ LUT Mode are activated then whenever the
TACH Reading Register value exceeds the Valid TACH Count Register setting, the FAN_STALL
status bit will be set.
When using the RPM based Fan Speed Control Algorithm (either FSC Mode or LUT with FSC
Mode), the stalled fan condition is checked whenever the Update Time is met and the fan drive
setting is updated. It is not a continuous check.
5.6.2
Aging Fan or Invalid Drive Detection
The EMC2103 contains circuitry that detects that the programmed fan speed can be reached by the
fan. If the target fan speed cannot be reached within a user defined band of tach counts at maximum
drive then the DRIVE_FAIL status bit is and the ALERT pin is asserted. This is useful to detect aging
fan conditions (where the fan’s natural maximum speed degrades over time) or incorrect fan speed
settings.
相关PDF资料 |
PDF描述 |
|---|---|
| CMX644AD5 | 1.2 kbps DATA, MODEM, PDSO24 |
| CMY211E6327 | 500 MHz - 2500 MHz RF/MICROWAVE DOUBLE BALANCED MIXER |
| CMZ5914BPTR13 | 3.6 V, 0.55 W, SILICON, UNIDIRECTIONAL VOLTAGE REGULATOR DIODE |
| CMZ5950BP | 110 V, 0.55 W, SILICON, UNIDIRECTIONAL VOLTAGE REGULATOR DIODE |
| CN201J1AS215DQ7 | Double Pole Power Rocker Switches |
相关代理商/技术参数 |
参数描述 |
|---|---|
| CMX644AD5 | 制造商:CML Innovative Technologies 功能描述:V22 AND Bell 212A Modem with DTMF, Tube |
| CMX649 | 制造商:CMLMICRO 制造商全称:CML Microcircuits 功能描述:ADM Codec |
| CMX649E3 | 制造商:CML Innovative Technologies 功能描述:Adaptive Delta Modulation (ADM) Voice Codec, Tube |
| CMX654 | 制造商:CMLMICRO 制造商全称:CML Microcircuits 功能描述:V23 Transmit Modulator |
| CMX661 | 制造商:CMLMICRO 制造商全称:CML Microcircuits 功能描述:The Product Data Amendment series of documents |
发布紧急采购，3分钟左右您将得到回复。