- 您现在的位置：买卖IC网 > PDF目录26505 > CP2102-GMR (SILICON LABORATORIES) PDF资料下载
参数资料
| 型号： | CP2102-GMR |
| 厂商： | SILICON LABORATORIES |
| 元件分类： | 总线控制器 |
| 中文描述： | UNIVERSAL SERIAL BUS CONTROLLER, QCC28 |
| 封装： | 5 X 5 MM, LEAD FREE, QFN-28 |
| 文件页数： | 3/18页 |
| 文件大小： | 373K |
| 代理商： | CP2102-GMR |
CP2102
Rev. 1.1
11
5. USB Function Controller and Transceiver
The Universal Serial Bus function controller in the CP2102 is a USB 2.0 compliant full-speed device with integrated
transceiver and on-chip matching and pull-up resistors. The USB function controller manages all data transfers
between the USB and the UART as well as command requests generated by the USB host controller and
commands for controlling the function of the UART.
The USB Suspend and Resume signals are supported for power management of both the CP2102 device as well
as external circuitry. The CP2102 will enter Suspend mode when Suspend signaling is detected on the bus. On
entering Suspend mode, the CP2102 asserts the SUSPEND and SUSPEND signals. SUSPEND and SUSPEND
are also asserted after a CP2102 reset until device configuration during USB Enumeration is complete.
The CP2102 exits the Suspend mode when any of the following occur: (1) Resume signaling is detected or
generated, (2) a USB Reset signal is detected, or (3) a device reset occurs. On exit of Suspend mode, the
SUSPEND and SUSPEND signals are de-asserted.
Both SUSPEND and SUSPEND temporarily float high during a CP2102 reset. If this behavior is undesirable, a
strong pulldown (10 k
) can be used to ensure SUSPEND remains low during reset. See Figure 6 for other
recommended options.
Figure 6. Typical Connection Diagram
Option 1: A 4.7 k
pull-up resistor can be added to increase noise immunity.
Option 2: A 4.7 F tantalum capacitor can be added if powering other devices from the on-chip regulator.
Option 3: Avalanche transient voltage suppression diodes should be added for ESD protection.
Option 3: Use Littlefuse p/n SP0503BAHT or equivalent.
Option 4: 10 k
resistor to ground to hold SUSPEND low on initial power on or device reset.
1
CP2102
SUSPEND
11
12
REGIN
7
GND
3
RST
9
D+
4
D-
5
8
C2
0.1
F
C1
1
F
RI
DCD
CTS
RTS
RXD
TXD
DSR
DTR
2
1
28
27
26
25
24
23
2
3
External RS-232
transceiver or
UART circuitry
(to external circuitry
for USB suspend
states)
VBUS
D-
D+
GND 4
5
6
USB
CONNECTOR
6
VDD
VBUS
VDD
R1
4.7 k
D1
D2
D3
Option 1
R2
10 k
Option 4
Option 3
C4
4.7
F
TANT
Option 2
相关PDF资料 |
PDF描述 |
|---|---|
| CP2103-GMR | |
| CP2104-F03-GM | |
| CP2105-F01-GM | |
| CP2110-F01-GM | |
| CPC1009NTR | |
相关代理商/技术参数 |
参数描述 |
|---|---|
| CP210-2N4416-CT | 功能描述:JFET N-Channel 30V 5mA @ 20V Surface Mount Die 制造商:central semiconductor corp 系列:- 包装:托盘 零件状态:有效 FET 类型:N 沟道 电压 - 击穿（V（BR）GSS）:30V 漏源极电压（Vdss）:30V 不同 Vds（Vgs=0）时的电流 - 漏极（Idss）:5mA @ 20V 漏极电流（Id） - 最大值:- 不同 Id 时的电压 - 截止（VGS 关）:6V @ 1nA 不同 Vds 时的输入电容（Ciss）:4pF @ 15V 电阻 - RDS（开）:- 安装类型:表面贴装 封装/外壳:模具 供应商器件封装:模具 功率 - 最大值:- 标准包装:1 |
| CP210-2N4416-CT20 | 功能描述:JFET N-Channel 30V 5mA @ 20V Surface Mount Die 制造商:central semiconductor corp 系列:- 包装:托盘 零件状态:有效 FET 类型:N 沟道 电压 - 击穿（V（BR）GSS）:30V 漏源极电压（Vdss）:30V 不同 Vds（Vgs=0）时的电流 - 漏极（Idss）:5mA @ 20V 漏极电流（Id） - 最大值:- 不同 Id 时的电压 - 截止（VGS 关）:6V @ 1nA 不同 Vds 时的输入电容（Ciss）:4pF @ 15V 电阻 - RDS（开）:- 安装类型:表面贴装 封装/外壳:模具 供应商器件封装:模具 功率 - 最大值:- 标准包装:1 |
| CP2102N-A01-GQFN20 | 功能描述:USB TO UART BRIDGE - QFN20 制造商:silicon labs 系列:* 零件状态:有效 标准包装:100 |
| CP2102N-A01-GQFN20R | 功能描述:USB Bridge, USB to UART USB 2.0 UART Interface 制造商:silicon labs 标准包装:1,500 |
| CP2102N-A01-GQFN24 | 功能描述:USB TO UART BRIDGE - QFN24 制造商:silicon labs 系列:* 零件状态:有效 标准包装:100 |
发布紧急采购，3分钟左右您将得到回复。