- 您现在的位置：买卖IC网 > PDF目录26505 > CP2110-F01-GM (SILICON LABORATORIES) PDF资料下载
参数资料
| 型号： | CP2110-F01-GM |
| 厂商： | SILICON LABORATORIES |
| 元件分类： | 总线控制器 |
| 中文描述： | UNIVERSAL SERIAL BUS CONTROLLER, QCC24 |
| 封装： | 4 X 4 MM, LEAD FREE, MO-220WGGD, QFN-24 |
| 文件页数： | 8/26页 |
| 文件大小： | 244K |
| 代理商： | CP2110-F01-GM |
CP2110
16
Rev. 1.1
6. USB Function Controller and Transceiver
The Universal Serial Bus (USB) function controller in the CP2110 is a USB 2.0-compliant, full-speed device with
integrated transceiver and on-chip matching and pullup resistors. The USB function controller manages all data
transfers between the USB and the UARTs as well as command requests generated by the USB host controller
and commands for controlling the function of the UARTs and GPIO pins.
The USB Suspend and Resume modes are supported for power management of both the CP2110 device as well
as external circuitry. The CP2110 enters Suspend mode when Suspend signaling is detected on the bus. Upon
entering Suspend mode, the Suspend signals are asserted. The Suspend signals are also asserted after a CP2110
reset until device configuration during USB Enumeration is complete. SUSPEND is logic high when the device is in
the Suspend state, and logic low when the device is in normal mode. The SUSPEND pin has the opposite logic
value of the SUSPEND pin.
The CP2110 exits Suspend mode when any of the following occur: Resume signaling is detected or generated, a
USB Reset signal is detected, or a device reset occurs. SUSPEND and SUSPEND are weakly pulled to VIO in a
high impedance state during a CP2110 reset. If this behavior is undesirable, a strong pulldown (10 k
) can be used
to ensure SUSPEND remains low during reset.
The logic level and output mode (push-pull or open-drain) of various pins during USB Suspend is configurable in
the PROM. See Section 9 for more information.
相关PDF资料 |
PDF描述 |
|---|---|
| CPC1009NTR | |
| CPC1009N | |
| CPC1014NTR | |
| CPC1014N | |
| CPC1019N | |
相关代理商/技术参数 |
参数描述 |
|---|---|
| CP2110-F01-GMR | 功能描述:输入/输出控制器接口集成电路 HID USB-UART bridge RoHS:否 制造商:Silicon Labs 产品: 输入/输出端数量: 工作电源电压: 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:QFN-64 封装:Tray |
| CP2110-F02-GM1 | 功能描述:输入/输出控制器接口集成电路 HID USB-UART bridge RoHS:否 制造商:Silicon Labs 产品: 输入/输出端数量: 工作电源电压: 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:QFN-64 封装:Tray |
| CP2110-F02-GM1R | 功能描述:输入/输出控制器接口集成电路 HID USB-UART bridge RoHS:否 制造商:Silicon Labs 产品: 输入/输出端数量: 工作电源电压: 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:QFN-64 封装:Tray |
| CP2110-GM | 制造商:Silicon Laboratories Inc 功能描述:USB TO UART BRIDGE 28QFN - Rail/Tube |
| CP2-11-10L | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog IC |
发布紧急采购，3分钟左右您将得到回复。