- 您现在的位置：买卖IC网 > PDF目录28816 > CPC1466DTR (CLARE INC) PDF资料下载
参数资料
| 型号： | CPC1466DTR |
| 厂商： | CLARE INC |
| 元件分类： | 通信及网络 |
| 中文描述： | SPECIALTY TELECOM CIRCUIT, PDSO16 |
| 封装： | ROHS COMPLIANT, SOIC-16 |
| 文件页数： | 2/15页 |
| 文件大小： | 309K |
| 代理商： | CPC1466DTR |
CPC1466
10
www.clare.com
R00B
P
R
EL
IM
INAR
Y
2. Functional Description
2.1 Introduction
The CPC1466 can be used for a number of DSL
designs requiring a dc hold circuit such as ADSL
modem applications. Typical ADSL applications will
use a filter circuit design similar to the one shown in
The DC Termination IC performs two fundamental
functions in an ADSL modem application; as an
electronic inductor providing a low impedance dc
termination with a high impedance ac termination and
second as part of the sealing current detection system
for automated line sensing. This function provides an
excellent method to monitor for the presence of
sealing current. Generally, loss of sealing current
indicates loop loss.
As can be seen in the application circuit in Figure 9 on
page 9, CPC1466 designs require few external
components. For the CPC1466, all that is needed is a
circuit protector, two resistors and a capacitor. To
ensure DSL signal integrity over a wide variety of
conditions a POTS splitter type filter is recommended
to isolate the DSL traffic from the termination.
2.2 Surge Protection
Although the CPC1466 self protects via current
limiting, it requires over-voltage surge protection to
protect against destructive over-voltage transients.
Clare recommends the use of a crowbar-type surge
protector to limit the surge voltage seen by the
CPC1466 to less than 250 V. The protection device
must be able to withstand the surge requirements
specified by the appropriate governing agency in
regions where the product will be deployed. Teccor,
Inc. and Bourns, Inc. make suitable surge protectors
for most applications. Devices such as Teccor’s
P1800SD or P2000SD Sidactors and Bourns’
TISP4220H3BJ or TISP4240H3BJ thyristors should
provide suitable protection.
2.3 Bridge Rectifier
The bridge rectifier in the CPC1466 ensures that the
device is polarity insensitive and provides consistent
operational characteristics if the tip to ring polarity is
reversed.
2.4 State Transitions
The dc tip to ring voltage-current characteristics of the
CPC1466 are shown in Figure 2 “I-V Requirements
Template, 0 V to 50 V”, and in Figure 3 “I-V
Transition timings are illustrated in Figure 6 “Applied
configuration for these timings is given in Figure 5
timing figures are located on page 7.
State transition timings are set by the 1
F capacitor
connected between the TC and COM pins.
2.4.1 Activation - On-State
Application of battery voltage to the loop causes the
CPC1466 to conduct whenever the voltage exceeds
approximately 35 V. With application of sufficient
voltage applied across the tip and ring terminals, the
CPC1466 will initially conduct a nominal 150
A of
sealing current for approximately 20 ms prior to
activation. Once activated, the CPC1466 will remain in
the on state for as long as the loop current exceeds a
nominal 0.5 mA.
The CPC1466 turn-on timing circuit assures device
activation will occur within 50 ms of an applied voltage
greater than 43.5 V but not within the first 3 ms.
2.4.2 Deactivation - Off-State
While the CPC1466 activation protocol is based on an
initial minimum voltage level, deactivation is based on
a diminished sealing current level. Deactivation occurs
when the nominal sealing current level drops below
0.5 mA with guaranteed deactivation occurring for
sealing current levels less than 0.1 mA
The turn-off timing circuit deactivates the sealing
current hold circuit when 1 mA of sealing current has
been removed for 100 ms but ignores periods of loss
up to 3 ms.
2.5 Photo-Diode (PD) Output Behavior
Output from the PD pin provides a minimum of 0.2 mA
of photodiode drive current for an optocoupler’s LED
anytime sealing current exceeds 1 mA.
Because LED current is interrupted whenever loop
current is interrupted, the optocoupler provides an
相关PDF资料 |
PDF描述 |
|---|---|
| CPC1560GSTR | |
| CPC1560GS | |
| CPC1560G | |
| CPC1590P | |
| CPC1590PTR | |
相关代理商/技术参数 |
参数描述 |
|---|---|
| CPC1466M | 制造商:CLARE 制造商全称:Clare, Inc. 功能描述:Broadband ADSL/VDSL DC Termination IC |
| CPC1466MTR | 制造商:CLARE 制造商全称:Clare, Inc. 功能描述:Broadband ADSL/VDSL DC Termination IC |
| CPC150400 | 制造商:SUPERWORLD 制造商全称:Superworld Electronics 功能描述:1000 Base-T Magnetic Modules |
| CPC150402 | 制造商:SUPERWORLD 制造商全称:Superworld Electronics 功能描述:1000 Base-T Magnetic Modules |
| CPC150403 | 制造商:SUPERWORLD 制造商全称:Superworld Electronics 功能描述:1000 Base-T Magnetic Modules |
发布紧急采购，3分钟左右您将得到回复。