- 您现在的位置：买卖IC网 > PDF目录20631 > CPD250-4530 (Power-One)PWR SUP 250W 3.3/5/12/-12V QUAD PDF资料下载
参数资料
| 型号： | CPD250-4530 |
| 厂商： | Power-One |
| 文件页数： | 9/19页 |
| 文件大小： | 0K |
| 描述： | PWR SUP 250W 3.3/5/12/-12V QUAD |
| 标准包装： | 10 |
| 系列： | CPD |
| 类型： | 隔离 |
| 输入电压： | 36 ~ 75V |
| 输出： | 5V，3.3V，±12V |
| 输出数： | 4 |
| 输出 - 1 @ 电流（最大）： | 5 VDC @ 40A |
| 输出 - 2 @ 电流（最大）： | 3.3 VDC @ 40A |
| 输出 - 3 @ 电流（最大）： | 12 VDC @ 5.5A |
| 输出 - 4 @ 电流（最大）： | -12 VDC @ 2A |
| 功率（瓦特）： | 250W |
| 安装类型： | Compact PCI® |
| 效率： | 82.2% |
| 封装/外壳： | 模块 |
| 尺寸/尺寸： | 6.40" L x 1.60" W x 5.07" H（162.5mm x 40.6mm x 128.7mm） |
| 包装： | 散装 |
| 电源（瓦特）- 最大： | 250W |
| 批准： | CE，CSA，cUL，EN，TUV，UL |
| 其它名称： | 179-2264 |
CPA, CPD Series Data Sheet
?
200 – 550 Watt
CompactPCI ?
AC-DC and DC-DC Converters
C i ext = ––––––––– 2 –– –––– 2 ––––––
Hold-upTimeofCPDModels
For extended hold-up time of CPD models, use external
output capacitors or decoupling diodes and input capacitors
of adequate size.
Formula for additional external input capacitor:
2 ? P o ? ( t h total – t h ) ? 100
η ? ( V ti – V i min )
whereas:
C i ext = external input capacitance [mF]
P o = output power [W]
h = efficiency [%]
t h total = total hold-up time [ms]
t h = hold-up time [ms]
V i min = minimum input voltage [V]
V ti = threshold level [V]
Note : After V i was removed, the outputs maintain their voltage
for the time t h . Even if V i comes back during t h , but after t h , the
output voltage might be affected.
Redundant Operation and Hot Swap
Due to the integrated ORing FETs/diodes, the converters are
designed to be operated in redundant systems.
Hot swap is also possible, but the output voltages of each
bus may deviate dynamically by ≤ 5% during the plug-in / plug-
out operation.
condition. If an overvoltage of 120 – 130% is detected, the
converter is permanently disabled. To reset, the input voltage
must be removed for 10 – 20 seconds.
Note : The models CPA500/550 with version number before
V110 need approx. 60 s to recover.
Thermal Considerations and Protection
If a converter is mounted in the upright position with airflow as
specified in the general conditions of the tables 4 and 5,
allowing unrestricted forced-air cooling, and is operated at its
nominal input voltage and power at maximum ambient
temperature T A max (see Temperatures ), the temperature at the
measurement point of the case temperature T C (see
Mechanical Data ) will approach after an initial warm-up
phase the indicated maximum value of T C max (105 °C).
However, the relationship between T A and T C depends heavily
on the operating conditions and the system integration. The
thermal conditions are significantly influenced by the input
voltage, the output current, the airflow, and the temperature of
the adjacent elements and surfaces. T A max is therefore,
contrary to T C max , an indicative value only.
Caution : The installer must ensure that under all operating
conditions T C remains within the limits shown in the diagrams
fig. 4.
P o / P o nom
Note : We recommend connecting some capacitors parallel to
the bus to limit voltage deviations during hot swapping and
1.0
JM011a
during switch-on / switch-off of the input voltage of one of the
parallel-connected converters.
Output Characteristic and Protection
All outputs are fully protected against continuous open-circuit
(no load) and continuous short-circuit conditions.
All outputs of CPx200/250 models have a constant current
limitation with a rectangular characteristic; see figure 3. In
0.6
0.5
Convection cooling
in upright position
250 LFM = 1.25 m/s
addition, the total power from outputs Vo1, Vo2, and Vo3 is
limited to P o max , resulting in a free choice of load distribution
0
T A min
40
50
60
70
80
90 °C
between these outputs. Output Vo4 is disabled in the case of
overtemperature generated by overcurrent.
In CPA500/550 and CPD500 models, the total power of all
four outputs is limited to P o max .
In all models, all outputs are monitored for an overvoltage
Fig. 4a
Output power versus temperature T A at V i nom (CPD/
CPA200)
P o / P o nom
V o / V o nom
1.0
I o nom
I o max
I o L
05186b
1.0
05190c
200 LFM = 1 m/s
0.95
Convection cooling
400 LFM = 2 m/s
in upright position
0.5
0.5
Fig. 3
0
I o
0
T A min
Fig. 4b
40
50
60
70
80
90 °C
Typical output characteristic V o versus I o
Output power versus temperature T A at V i nom (CPD/CPA250)
BCD20005-G Rev. AG2, 20-Dec-2012
Page 9 of 19
www.power-one.com
相关PDF资料 |
PDF描述 |
|---|---|
| LTC3700EMS#PBF | IC REG DL BUCK/LINEAR 10MSOP |
| RCM06DTBI-S189 | CONN EDGECARD 12POS R/A .156 SLD |
| EBM08DSAN | CONN EDGECARD 16POS R/A .156 SLD |
| RW2-2412D/H3/SMD | CONV DC/DC 2W 18-36VIN +/-12VOUT |
| AMM25DSEN-S13 | CONN EDGECARD 50POS .156 EXTEND |
相关代理商/技术参数 |
参数描述 |
|---|---|
| CPD250-4530AG | 功能描述:PWR SUP 250W 3.3/5/12/-12V QUAD 制造商:bel power solutions 系列:* 零件状态:有效 标准包装:20 |
| CPD250-4530CG | 功能描述:DC/DC CONVERTER 制造商:bel power solutions 系列:Melcher CPD 包装:散装 零件状态:有效 类型:隔离 电压 - 输入:36 ~ 75 V 输出:5V，3.3V，12V，-12V 输出数:4 不同电流时的输出（最大值） - 1:5 VDC @ 40A 不同电流时的输出（最大值） - 2:3.3 VDC @ 40A 不同电流时的输出（最大值） - 3:12 VDC @ 5.5A 不同电流时的输出（最大值） - 4:-12 VDC @ 2A 功率（W）:250W 应用:ITE（商业） 安装类型:Compact PCI? 工作温度:-25°C ~ 50°C 效率:82.2% 封装/外壳:- 大小/尺寸:6.67" 长 x 3.94" 宽 x 1.60" 高（169.5mm x 100.0mm x 40.6mm） 功率（W） - 最大值:250W 认可:cCSAus，CE，TUV 标准包装:20 |
| CPD250-4530G | 功能描述:DC/DC转换器 36-75Vin 250W 5V25A 3.3V20A /12V4A RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| CPD250-4530-G | 制造商:Power-One 功能描述: |
| CPD250-4530GREP | 制造商:Power-One 功能描述: |
发布紧急采购，3分钟左右您将得到回复。