- 您现在的位置：买卖IC网 > PDF目录20624 > CS5462-ISZR (Cirrus Logic Inc)IC ENERGY METERING 1PHASE 24SSOP PDF资料下载
参数资料
| 型号： | CS5462-ISZR |
| 厂商： | Cirrus Logic Inc |
| 文件页数： | 11/16页 |
| 文件大小： | 0K |
| 描述： | IC ENERGY METERING 1PHASE 24SSOP |
| 标准包装： | 1,000 |
| 输入阻抗： | 30 千欧 |
| 测量误差： | 0.1% |
| 电压 - 高输入/输出： | 0.8V |
| 电压 - 低输入/输出： | 0.2V |
| 电流 - 电源： | 2.9mA |
| 电源电压： | 4.75 V ~ 5.25 V |
| 测量仪表类型： | 单相 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-SSOP（0.209"，5.30mm 宽） |
| 供应商设备封装： | 24-SSOP |
| 包装： | 带卷 (TR) |
CS5462
4.2.2
Mechanical Counter Format
C AL 1
C AL 0
In mechanical counter mode, the CS5462 produc-
es pulses on E1 and E2 which can be used to drive
a bi-directional mechanical counter. Each pin pro-
duces active-low pulses which have pulse widths
of 125 ms or 15 ms, depending on the frequency
selected. In the figure below, the frequency and
corresponding pulse width is shown for each op-
tion available. In this mode when energy is posi-
P1
P2
P3
P4
P5
P6
P7
+ 4.2%
+ 2.8%
+ 1.4%
0%
-1.4%
-2.8%
-4.2%
+ 0.6%
+ 0.4%
+ 0.2%
0%
-0.2%
-0.4%
-0.6%
tive, the pulses appear on E1; when energy is
negative, pulses appear on E2.
Figure 6. Calibration Options
This calibration is accomplished by connecting
E1
E2
FREQ
connected to:
Frequency
Pulse Width
Positive Energy
P6
2 Hz
125 ms
pulse width
P7
16 Hz
15 ms
pulse width
Negative Energy
each Configuration Input pin, CAL1 and CAL0, to
one of the Program Select Output pins, P1 - P7. At
startup the CS5462 will scan the CAL1 and CAL0
pins to discern what connections are made, and
then calibrate the gain accordingly.
CAL1 and CAL0 each have seven options which
allows for 49 different steps of 0.2% between
+4.8% and -4.8% of expected energy output. Be-
fore startup, CAL1 and CAL0 must each be con-
4.3
Energy Direction Indicator
nected to only one of the program select pins.
For either pulse output mode, the NEG pin can be
used to indicate the direction of the energy calcu-
lated. The NEG pin is updated at the sample rate
of the converter. If negative energy is detected the
NEG pin will become active low and will remain ac-
tive low until positive energy is detected.
4.4 Internal Calibration Option
For most power meter applications the standard
accuracy requirements require the meter be cali-
brated to within a certain percentage. Calibrating a
CS5462 meter can be done a number of ways.
One calibration method is to externally adjust the
front-end input circuit by using a potentiometer or
resistor network. By adjusting the amount of gain in
the resistor divider on the front end the energy out-
puts can be adjusted to fit the accuracy required.
Although this method is available, it may be costly
to add the additional components and the accuracy
required is often difficult to achieve. As an alterna-
tive the CS5462 is designed to allow the user to
calibrate the part without the need for external po-
tentiometers or resistor networks. The CS5462
provides a digital on-chip calibration solution. This
digital alternative can calibrate energy registration
error to within 0.1% without any analog adjust-
ments.
DS547F1
To Calibrate the CS5462:
1. Connect CAL1 and CAL0 to P4. This connection
will adjust the energy outputs by 0%.
2. Apply known current and voltage signals to the
inputs of the CS5462.
3. Measure the average pulse output frequency of
FOUT, E1, or E2.
4. The average frequency will be within some per-
centage of the expected frequency. Depending on
the output of the uncalibrated chip, the CAL0 and
CAL1 pins can be adjusted using the above options
(see “User Defined Settings” on page 12 for more
on calibration) .
4.5 Power-on Reset
The CS5462 is equipped with internal circuitry that
will put the chip into reset if power supply is lost.
This is particularly useful in black-out or brown-out
situations in which the power supply temporarily in-
terrupted. The CS5462 will enter into reset if the
power drops below 2.5 V. The chip will remain in
reset until the supply rises to 4 V (See Figure 6) at
11
相关PDF资料 |
PDF描述 |
|---|---|
| EB73S-SA1060W-K | CONN EDGEBOARD SINGLE 10POS 5A |
| EB71S-SA1060X | CONN EDGEBOARD SINGLE 10POS 3A |
| LT3500HMSE#PBF | IC REG DL BUCK/LINEAR 16-MSOP |
| 591D477X96W3R2T20H | CAP TANT 470UF 6.3V 10% 2824 |
| LT3694IUFD-1#PBF | IC REG TRPL BUCK/LINEAR 28QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| CS5463 | 制造商:CIRRUS 制造商全称:Cirrus Logic 功能描述:Single Phase, Bi-directional Power/Energy IC |
| CS5463_08 | 制造商:CIRRUS 制造商全称:Cirrus Logic 功能描述:Single Phase, Bi-directional Power/Energy IC |
| CS5463_11 | 制造商:CIRRUS 制造商全称:Cirrus Logic 功能描述:Single Phase, Bi-directional Power/Energy IC |
| CS5463-IS | 功能描述:电流和电力监控器、调节器 Single Phase Power/Energy IC RoHS:否 制造商:STMicroelectronics 产品:Current Regulators 电源电压-最大:48 V 电源电压-最小:5.5 V 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:HPSO-8 封装:Reel |
| CS5463-ISZ | 功能描述:电流和电力监控器、调节器 Single Phase Power/Energy IC RoHS:否 制造商:STMicroelectronics 产品:Current Regulators 电源电压-最大:48 V 电源电压-最小:5.5 V 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:HPSO-8 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。