- 您现在的位置：买卖IC网 > PDF目录20639 > CS5467-ISZ (Cirrus Logic Inc)IC ENERGY METERING 1PHASE 28SSOP PDF资料下载
参数资料
| 型号： | CS5467-ISZ |
| 厂商： | Cirrus Logic Inc |
| 文件页数： | 22/46页 |
| 文件大小： | 0K |
| 描述： | IC ENERGY METERING 1PHASE 28SSOP |
| 特色产品： | CS546X IC Family |
| 标准包装： | 47 |
| 输入阻抗： | 30 千欧 |
| 测量误差： | 0.1% |
| 电压 - 高输入/输出： | 0.8V |
| 电压 - 低输入/输出： | 0.2V |
| 电流 - 电源： | 3.5mA |
| 电源电压： | 4.75 V ~ 5.25 V |
| 测量仪表类型： | 单相 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-SSOP（0.209"，5.30mm 宽） |
| 供应商设备封装： | 28-SSOP |
| 包装： | 管件 |
| 产品目录页面： | 754 (CN2011-ZH PDF) |
| 配用： | 598-1555-ND - BOARD EVAL FOR CS5467 ADC |
| 其它名称： | 598-1197-5 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页当前第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页
CS5467
For each enabled input channel, the measured value is
rectified and compared to the associated level register .
Over the duration window, the number of samples
above and below the level are counted. If the number of
samples below the level exceeds the number of sam-
ples above, a Status register bit V1 SAG (V2 SAG ),
I1 FAULT (I2 FAULT ) is set, indicating a sag or fault condi-
tion. (see Figure 8 )..
Figure 8. Sag and Fault Detect
6.12 Epsilon
The Epsilon register is used to set the gain of the 90°
phase shift used in the quadrature power calculation.
The value in the Epsilon register is the ratio of the line
frequency to the output word rate (OWR). It is, by de-
fault, 50/4000 (0.0125), for 50 Hz line and 4000 Hz sam-
ple (OWR) frequencies.
For 60 Hz line frequency, it is 60/4000 (0.015). Other
output word rates (OWR) can be used.
Epsilon can also be calculated automatically by the
CS5467 by setting the AFC bit in the Mode Control
( Modes ) register. The Frequency Update bit (FUP) in
the Status register is set every time the Epsilon register
has been automatically updated.
6.13 Temperature Measurement
The on-chip temperature sensor is designed to mea-
sure temperature and optionally compensate for tem-
perature drift of the voltage reference. It uses the V BE of
a transistor to determine temperature.
In the CS5467, voltage2 and temperature are multi-
plexed on one ADC channel. To initiate a temperature
measurement, write 1 to the Temperature Measure-
ment ( T MEAS ) register. T MEAS will go through counts 1,
2, 4, and back to 0. Wait for T MEAS to return to 0. When
done, Temperature ( T ) is updated. The Status register
bit TUP also indicates when the Temperature register is
22
updated. The Voltage2 register ( V2 ) will not update dur-
ing the temperature measurement, but resume mea-
surement afterwards.
Temperature measurements are stored in the Temper-
ature register ( T ) which, by default, is configured to a
range of ±128 degrees on the Celsius (°C) scale.
The application program can change both the scale and
range of Temperature ( T ) by changing the Temperature
Gain ( T GAIN ) and Temperature Offset ( T OFF ) registers.
Two values must be known — the transistor’s ? V BE per
degree, and the transistor’s V BE at 0 degrees. At the
time of this publication, these values are:
?? V BE (per degree) = 0.2769523 mV/°C or °K
V BE 0 = 79.2604368 mV at 0°C
To determine the values to write to T GAIN and T OFF , use
the following formulae:
T GAIN = AD FS / ? V BE / T FS x 2 17
T OFF = -V BE 0 / AD FS x 2 23
In the above equations, AD FS is the full-scale input
range of the temperature A/D converter or 833.333 mV
and T FS is the desired full-scale range of the Tempera-
ture ( T ) register. The binary exponents are the bit posi-
tions of the binary point of these registers.
To use the Celsius scale (°C) and cover the chip’s oper-
ating temperature range of -40°C to +85°C, the Temper-
ature register range needs to be ±128 degrees. T FS
should be 128 degrees.
T GAIN = 833.333 / 0.2769523 / 128 x 131072
= 3081155 (0x2F03C3)
T OFF = -79.2604368 / 833.333 x 8388608
= -797862 (0xF3D35A)
These are the actual default values for these registers.
T GAIN and T OFF can also be used to calibrate the gain
and/or offset of the temperature sensor or A/D convert-
er. (See Section 9. System Calibration on page 40).
To use the Kelvin (°K) scale, simply add 273 times ? V BE
/ AD FS x 2 23 to T OFF since 0°C = 273°K,. You will also
need more range. Since -40°C to +85°C is 233°K to
358°K, a T FS of 512 degrees should be used in the
T GAIN calculation.
To use the Fahrenheit (°F) scale, multiply ? V BE by 5/9
and add 32 times the new ? ? V BE ? / AD FS x 2 23 to T OFF
since 0°C = 32°F. You will also want to use a ? T FS of 256
degrees to cover the -40°C to +85°C range.
DS714F3
相关PDF资料 |
PDF描述 |
|---|---|
| GBC10DREH-S13 | CONN EDGECARD 20POS .100 EXTEND |
| VI-J5H-EW-B1 | CONVERTER MOD DC/DC 52V 100W |
| CS5460A-BSZ | IC ENERGY METERING 1PHASE 24SSOP |
| T95Z156K020ESSL | CAP TANT 15UF 20V 10% 2910 |
| DFN0.83BK | DURA-FLEX .83" BLACK 100' |
相关代理商/技术参数 |
参数描述 |
|---|---|
| CS5467-ISZR | 功能描述:电流和电力监控器、调节器 IC 4-Ch Single Phase PWR/Energy RoHS:否 制造商:STMicroelectronics 产品:Current Regulators 电源电压-最大:48 V 电源电压-最小:5.5 V 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:HPSO-8 封装:Reel |
| CS5471 | 制造商:CIRRUS 制造商全称:Cirrus Logic 功能描述:DUAL CHANNEL DELTA SIGMA ANALOG TO DIGITAL CONVERTER |
| CS5471-BS | 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:Cirrus Logic 功能描述: |
| CS5471-BSR | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| CS547233-ISZR | 功能描述:模数转换器 - ADC IC 24-bit 2-ch Delta Sigma ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
发布紧急采购，3分钟左右您将得到回复。