- 您现在的位置：买卖IC网 > PDF目录20639 > CS5467-ISZ (Cirrus Logic Inc)IC ENERGY METERING 1PHASE 28SSOP PDF资料下载
参数资料
| 型号： | CS5467-ISZ |
| 厂商： | Cirrus Logic Inc |
| 文件页数： | 41/46页 |
| 文件大小： | 0K |
| 描述： | IC ENERGY METERING 1PHASE 28SSOP |
| 特色产品： | CS546X IC Family |
| 标准包装： | 47 |
| 输入阻抗： | 30 千欧 |
| 测量误差： | 0.1% |
| 电压 - 高输入/输出： | 0.8V |
| 电压 - 低输入/输出： | 0.2V |
| 电流 - 电源： | 3.5mA |
| 电源电压： | 4.75 V ~ 5.25 V |
| 测量仪表类型： | 单相 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-SSOP（0.209"，5.30mm 宽） |
| 供应商设备封装： | 28-SSOP |
| 包装： | 管件 |
| 产品目录页面： | 754 (CN2011-ZH PDF) |
| 配用： | 598-1555-ND - BOARD EVAL FOR CS5467 ADC |
| 其它名称： | 598-1197-5 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页当前第41页第42页第43页第44页第45页第46页
CS5467
9.1.2 Gain Calibration
During gain calibration, a full-scale reference signal
must be applied to the meter or optionally, scaled to the
VIN1 ??? VIN2 ?? , ? IIN1 ? (IIN2 ??? pins of the CS5467. A DC
reference must be used for DC gain calibration. Either
an AC or DC reference can be used for RMS AC calibra-
tions. If DC is used, the associated high-pass filter
(HPF) must be off.
External
Connections
During AC gain calibration the RMS level of the applied
reference is measured with the preset gain, then divided
into 0.6 and the quotient stored back into the corre-
sponding gain register.
9.1.2.2 DC Gain Calibration
With a DC reference applied, the DC Gain Calibration
command measures and averages DC values read on
the specified voltage or current channels and stores the
reciprocal result in the associated gain registers, con-
verting measured voltage into needed gain. Subse-
quent conversions will use the new gain value.
-
-
R eference
Signal
CM
+
+
IN+
IN-
+
-
XG AIN
+
-
9.1.3 Calibration Order
1. DC offset.
2. DC or AC gain.
3. AC offset (if needed).
If both AC gain and offset calibrations were performed,
Figure 12. System Calibration of Gain.
Using a reference that is too large or too small can
cause an over-range condition during calibration. Either
condition can set Status register bits I1OR (I2OR)
V1OR (V2OR) for DC and I1ROR (I2ROR) V1ROR
(V2ROR) for AC calibration.
Full scale (FS) for the voltage input is ±250 mV peak
and for the current inputs is ±250 mV or ±50 mV peak
depending on selected gain range. The normal peak
voltage applied to these pins should not exceed these
levels during calibration or normal operation.
The range of the gain registers limits the gain calibration
range and subsequently the range of the reference level
that can be applied. The reference should not exceed
FS or be lower than FS/4.
9.1.2.1 AC Gain Calibration
Full scale for AC RMS gain calibrations is 60% of the in-
put’s full-scale range, which is either 250 mV or 50 mV
depending on the gain range selected. That’s 150 mV or
30 mV, again depending on range. So the normal refer-
ence input level should be either 150 or 30 mV RMS , AC
or DC.
Prior to executing an AC Gain Calibration command,
gain registers for any channel to be calibrated should be
set to 1.0 if the reference level mentioned above is
used, or to that level divided by the actual reference lev-
el used.
DS714F3
it is possible to repeat both to obtain additional accuracy
as AC gain and offset may interact.
9.1.4 Temperature Sensor Calibration
Temperature sensor calibration involves the adjustment
of two parameters - ? V BE and V BE 0. These values must
be known in order to calibrate the temperature sensor.
22 for an explanation of ? V BE and V BE 0 and how to cal-
culate T GAIN and T OFF register values from them.
9.1.4.1 Temperature Offset Calibration
Offset calibration can be done at any temperature, but
should be done mid-scale if any gain error exists.
Subtract the measured T register temperature from the
actual temperature to determine the offset error. Multi-
ply this error by ? V BE and add it to V BE 0 to yield a new
V BE 0 value. Recalculate T OFF using this new value .
9.1.4.2 Temperature Gain Calibration
Two temperature points far enough apart to give rea-
sonable accuracy, for example 25°C and 85°C, are re-
quired to calibrate temperature gain.
Divide the actual temperature difference by the mea-
sured ( T register) difference for the two temperatures.
This gives a gain correction factor. Update the T GAIN
register by multiplying it’s value by this correction factor.
Update ? V BE by dividing its old value by the gain cor-
rection factor. It will be needed for subsequent offset
calibrations.
41
相关PDF资料 |
PDF描述 |
|---|---|
| GBC10DREH-S13 | CONN EDGECARD 20POS .100 EXTEND |
| VI-J5H-EW-B1 | CONVERTER MOD DC/DC 52V 100W |
| CS5460A-BSZ | IC ENERGY METERING 1PHASE 24SSOP |
| T95Z156K020ESSL | CAP TANT 15UF 20V 10% 2910 |
| DFN0.83BK | DURA-FLEX .83" BLACK 100' |
相关代理商/技术参数 |
参数描述 |
|---|---|
| CS5467-ISZR | 功能描述:电流和电力监控器、调节器 IC 4-Ch Single Phase PWR/Energy RoHS:否 制造商:STMicroelectronics 产品:Current Regulators 电源电压-最大:48 V 电源电压-最小:5.5 V 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:HPSO-8 封装:Reel |
| CS5471 | 制造商:CIRRUS 制造商全称:Cirrus Logic 功能描述:DUAL CHANNEL DELTA SIGMA ANALOG TO DIGITAL CONVERTER |
| CS5471-BS | 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:Cirrus Logic 功能描述: |
| CS5471-BSR | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| CS547233-ISZR | 功能描述:模数转换器 - ADC IC 24-bit 2-ch Delta Sigma ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
发布紧急采购，3分钟左右您将得到回复。